Thanks to the built-in electronics, the washing machine during the operation performs the programmed action algorithm. For different reasons, electronics may fail, as a result of which the machine stops during the washing process. Some reasons for this malfunction can be eliminated independently, and for serious repairs will have to contact the service.
If the washing machine got up during washing and does not perform the specified actions, there may be several reasons for this. The most common are:
- engine breakdown;
- Binding of the Tan;
- faulty electronics;
- Course Castle Lock Loading.
By the nature of the action of the washing machine, the machine can be determined which item came to disqual.
Often the reason for stopping the washing machine is not a technical failure, but a person’s error. If household appliances suddenly stopped working, you need to check if the error errors were not allowed.
- The weight of the loaded linen exceeds the permissible rate. In the instructions attached to each washing machine, there is information on maximum loading. If you exceed the norm, then after a short time after switching on the machine will stop the work. For convenience in some models there is a special intelligent sensor, showing the level of permissible norms.
- Most washing machines have a mode called “delicate wash”. It is provided for washing delicate types of fabrics. In this mode, the machine can “shy” for a few seconds. Some users believe that such a stop is some kind of failure. But actually it is not.
- In the tank of the washing machine there was an imbalance. If one washing was simultaneously loaded large and small things, they can ride in a single com. For example, such often happens when the other things fall into a duvet cover. In this case, an imbalance may occur. In the washing machine, a special sensor is triggered, after which it turns off.
- In some cases, people themselves are to blame for the fact that in the work of the washing machine there is a failure. So, by mistake, the user can set the technique at once several washing modes, with the result that the electronics begins to fail. For example, while switching on the “Pre-Wash” and “Whitening” modes, it fails, because in any model, the joint inclusion of these modes is unacceptable. As a result, after a while the machine turns off and stops washing. In this case, an error message appears on the display.
In addition to the above reasons, stopping in the work of the washing machine can cause the absence of water flow. And, that is characteristic, the machine will turn on and starts to work, but in 3-5 minutes will stop and will feed the corresponding signals.
And stop can occur due to too weak head. For example, when the pressure in the pipes is weak, or an additional water consumption is carried out indoors.
With the climbing sewage, the problem is already lies not only in the washing machine. We will have to do the cleaning of the drain and the entire sewer system in the room. As soon as the zoom is eliminated, and the drains are free – the washing machine will continue its work in normal mode.
Elimination of the problem
If a TEN does not work, then the car will hang at the very beginning of the washing process. Since water heating does not happen, the entire further process will be broken.
Pollution of the drain system can be assumed if the washing machine stopped operation at the prescript stage. Most likely, the filter or nozzle is clogged near the drain pump.
If the plum filter is clogged, then this problem can be solved on its own, spending only 15-20 minutes. Need to clean the filter or if you wish to replace it with a new.
If the washing machine stopped working at the very beginning of operation, it may be caused in the broken door of the hatch. To begin with, it is necessary to check whether it is closed tightly, and only then (if the breakdown still revealed) to seek help in a service center.
In the case when the faults are not detected, it should be checked if everything was done correctly during operation.
Detected errors can be easily corrected depending on the type of origin.
- If the maximum permissible load is exceeded, you just need to remove excess underwear, and start the program for the washing machine.
- With the selected mode “Delicate Wash” machine stops not because it turned off, but because it is programmed. If the machine does not drain the water for a long time, it is necessary to activate the “Forced Dummy” mode (in different models it can be called differently), and then the “Spin” function.
- If an imbalance is observed in the tank of the washing machine, it is necessary to drain the water, activating the corresponding mode. After the process is completed, you need to get underwear and download again by distributing it uniformly. To avoid such situations, it is recommended to sort things before washing. You need to do it according to the principle – large wash separately from small.
- Before starting the washing machine, it is necessary to preview the water access. Check out its presence in the crane, then turn the crane on the pipe leading to the car.
In the event of an incomprehensible and unforeseen stop of the washing machine, a series of actions can be taken to help restore the washing process.
- Perform a reboot of the car. If it’s not a serious breakage, then in most cases it will help. You can additionally open the hatch (if the door is unlocked) and put underwear in a new way.
- Need to check whether the door is well covered, and some thing got it between it and the case. It should be remembered that with proper closing the hatch must be clearly heard a characteristic click.
- When you stop the operation, the machine on the screen gives some error. In this case, you need to refer to the instructions and compare the data. Most likely, the decryption of the error code will be indicated in the annotation.
If the cause of the stop is in a weak water pressure, it is necessary to increase it (if it seems possible). Need for the time of the fence of water for washing stop using it for other purposes (open a tap with water in the kitchen and so on). With a normal flow, the work will be restored within a few seconds, while the reboot will not need.
In cases where it was decided to immediately independently repair, important rules should be remembered. The main thing is possible only after complete de-energization of household appliances. You need to make sure that the washing machine is disabled from the network. And also to avoid the flood, you need to overlap the flow of water. Install on the washing machine only the details of the manufacturer purchased from proven suppliers. Retroped independent repair can be broken by the breakdown of the entire product.
If you independently identify the cause of the failure and it is not possible to eliminate it, it is necessary to contact the service center for the help of professionals.
About solving the problem on the example of the Bosch model see below.