Replacing any extensive parts of the washing machine for new ones with the help of masterservice masters – the service is not cheap. Usually even for replacing the cuffs take as much as it is. Change any detail, including the seal, can and independently.
Why need a seal?
Luke closes tightly and does not let water due to rubber or silicone seal. It is extreme Important detail that does not allow flooding, Along with serviceable nozzles, hoses and valves. Splashes raised by the drum in the process of washing and spinning remain inside the washing compartment.
Signs and causes of malfunction
The main sign of a faulty cuff is the leakage of water both during washing, and when rinsed and annealing. In this gum appear hurry, cracks and holes.
Than hot water, less high-quality powder than it is laid in a washing machine, the sooner the sealing gum is extended.
Silicone sealer is able to work without any problems 10 years 10, especially when SMA is quite expensive. The manufacturer, which is a deserved and authoritative brand, does not save on the quality of materials and technological processes of the manufacture of parts.
No matter how high quality parts, they are subject to gradual wear. The cuff cracks from frequent overheating, when you erase in boiling water, due to the use of special bleaching reagents, loaded both separately and contained in an expensive washing powder. Its influence and washed off the boiler for the scale (and the remedy for it), excessive rigidity of water, as well as the late cleaning of the sealer from the mold formed on it. The latter is the most dangerous: the mold itself is quite adaptable to new conditions. Sprout in any material, including rubber, it urgently spoils him over time. In addition to mold, danger is different types of fungus. Creating growths on the surface of the seal, they break the external smooth outline of the cuff.
In the closed state, the hatch remains the lumens, which is why the solution of the washing powder and the wastewater formed after washing leakage. Because of this, the car can use an additional podaching of water by opening the dummy valve, which reduces the concentration of the washing powder, reduces the quality of washing and leaves the puddles on the floor near SM.
Other signs are:
- the inability to close the hatch;
- Outsided sounds when working washing machine.
The cause of the abrasion of the cuff can be clashes of bras, suites with visors, shoes with unnecessary soles, metal lightning locks and buttons on clothes, coarse overalls, not pulled out of pockets, coins, fasteners and much more.
There were cases that the car passed water after accidentally postponed the iPhone, not taken out of his pocket. The metal frame of this smartphone, the fitting device around the perimeter, tried his black case, namely: threw a thinning CM cage in several places.
Any electrical appliance, including washing machines, with a negligent treatment will soon be broken. His damage is capable and not completely neat transportation, for example, when moving to a new apartment.
As for washing, then It is permissible to use easily permeable for water and washing powder Special bags, as well as turn the clothes inside out. The latter will protect the drum, cuff and the hatch door from the clashes, locks, buttons and bleaks, from which they are impossible to free.
How to remove?
Regardless of the model of the washing machine, remove and replace the cuff easily. You will need dummy and / or hexagon keys, perhaps the passage. Even a kitchen knife is suitable as a technical blade-lever – if you want to break the latches along the line of the hatch. Some models, for example, from the manufacturer Samsung or LG, allow you to remove the clamp not in one, and in two stages: a significant disassembly of the case will be required.
Before starting work, mandatory remove the location of bolts and wires on the smartphone. Some lay out the pulled bolts in the “chronological” order – after replacing the faulty parts, the fasteners return to the place in the reverse order.
This is a frame holding a manhole curl on its front wall. Having found a leak, turn on the alarm of the tank content and wait until all the water strokes. Lingerie must be achieved by hand. De-in the washing machine and Perform a number of steps.
- Find a latch on the hatch (if the clamp plastic). Take the one part of it where the latches are located. If it is a wire clamp – unscrew the screw or pitch using a sprinkle with a screw. The spring itself is located on the side of the Luke Door blocker either at its bottom.
- Beg and remove the clamp.
- Get rubber band inside the drum. At the first stage, she does not take off – she keeps her second clamp.
Before pulling out the cuff, find two labels, one of which is located on the rubber band, the other – on the drum. They must coincide. If there are no labels – march them.
For the final removal of the seal, most models will need to remove the front panel.
To remove it to do several actions.
- Unscrew the bolts from the back of the back wall, remove the entire “roof” of SM.
- Remove the tray for washing powder. Under it are located bolts that hold the dashboard – unscrew them.
- Lift the latches holding the dashboard and remove it. Actions should not be made with excessive force – if you damage the latches, the panel will not hold reliably after the assembly. Restored latches glued even the best glue, put reliable fixation of the panel.
- To remove the wiring (loops, wiring harvesters) from the panel is optional – it is enough to temporarily suspend, for example, with a tape.
- Dislign the bolts from the front of the case.
- Remove the lid, stepping filter of the pumping pump, and unscrew the bolt under it.
- Pretty the lower part of the front panel – it is fixed on large snaps.
- Unscrew the bottom and upper bolts.
- Remove and move to the side of this part of the panel.
Remove the device locking device (activated when washing) there is no need. The second clamp will be available.
He is filmed the same as the first. The gum is located on the counterweight and is also completely dismantled.
To remove this wire (or cable) clamp, make simple operations.
- Remove the counterweight by unscrewing the screws that hold them.
- Carefully remove the clamp. His no longer holds.
Torn the protruding cuff. Wear a new one – and repeat the previous steps in the reverse order.
Cleaning and repair
The new cuff is not put in some cases.
- In the city or district No service center in which accessories for washing machines are available In full assortment. Order can be delivered after a period of several days to 2-3 months. Notify the brand and model of the machine to employee service center. Until the desired detail comes, it is most likely to erase.
- At the moment you are limited in spending. At the first opportunity, you should buy or order a new cuff.
- The model of this SMA has long been removed from production, Standards and sizes Cuffs have changed, find this spare part unreal. Only the garbage truck can help.
The worst scenario – attempts to make a cuff alone From a suitable car or camera for cars. The fact is that not every owner of the washing machine, especially the expensive model, working so far and properly, will throw off the unit due to the fact that there were no cuffs for CM. Attempts to repair the old or cut out of the air chamber new ones are made by the owner of mothers repeatedly.
Experiments to turn the device in SMI with vertical loading, running the spin on small (less than 200 per second) turnover, or washing, in general, without it, and turning off the boiler. But such a remission of the unit justifies. The washing compartment (tank) with a drum impenetrable for water – in normal mode when the splashes are sprayed in all directions. And yet the load on the motor in the “lying” position of the machine increases sharply. It is impossible to take advantage of the classic algorithm for wool, silk and other tissues requiring a special approach.
Some models of the same brand can be compatible – not all the details in them differ in size and appearance.
For cleaning from mold and fungus, branded materials will be required.
- Rafting (any). It does not matter whether this rag has a pile: shine and radiating cuff is not required, it is almost all the time closed by the Luke door frame.
- Ethanol. Vodka wipe is not recommended – it contains sugar.
You can try cologne as a solvent.
Do not use the “646th” solvent and dichloroethane – they dissolve almost all types of plastics. Do not rub the rubber with abrasive detergent without dilution with water, do not use the sandpaper when cleaning – you are even more thinning the gasket.
If traces from spiders are found in your washing machine, ant and cockroaches, take advantage of this repair – and clean all the insides where they nesting. Pure not only outside, but also from the inside the washing machine will work long. It often happens that in the house in which the cockroaches, broken techniques, even to be repaired, is thrown away – few people take it to repair. So, the excrement of cockroaches remove from everywhere not easy: it will be necessary to wash the mechanics and parts of the housing, internal racks in the soap solution. Electronics are immersed in a solution of alcohol or acetone – either blurred from a high-pressure washing operating in air blowing mode (without water). All these actions are quite expensive.
Take advantage of waterproof glue with good adhesion to glue the piping on the fiber place. The glue must glue the rubber reliably, while not afraid of soapy water, which is essentially a solution of washing powder. The plasticity restored thus rubber should remain unchanged.
- At the same time, the patch should exceed the thickness of the stolen place – otherwise the defect will soon form. If necessary – several thin layers are glued together.
- It is advisable to “sand” shallow sandpaper bonded surfaces.
- As a degreasing agent use alcohol or acetone.
- Lubricated with a sealant (or any shoe glue) a patch and a cuffs withstand a few minutes – either pressed immediately. The best option is to clamp in the vice with the help of wooden or plastic plates.
Pack the gum in the places of bends will not be able to. You can try to vulcanize with a piece of raw rubber, Heating the fastened saint soldering iron, heated to 200 degrees. At the same time, the “sand” may not be required: Polymer rubber molecules and additives during heating are distributed at the place of gluing, there is a hot diffusion of solid bodies (rubber) to each other according to the laws of physics.
Applies seam to break. Seam enhances the wear resistance and strength of the recovered zone. Repair as a whole will not save SMA from replacing worn gum: water sooner or later will fall into e-board. The slightest closure of the tracks on the printed circuit board will immediately derive sensitive chips in order – soap solutions and natural minerals contained in water carry out electric current.
Installation of the cuff
Little to remove the clamps and dismantle the old cuff. In addition, it is not completely symmetrical – it is not plastic, but a much softer material. However, the “factory” deformation will not affect the performance of the part. The cuff is growing up and “swept” from all sides to its place. Need to install a new one.
Consider what needs to be done for this.
- Apply the cuff and achieve the installation labels and technological gaps, the holes coincided. It is better to immediately install it right than to delay backwards.
- Grasp the edges of the cuff and pull it on the edge of the tank. Rubber stretch is very difficult, with the first attempt the action may fail. Excessive force will lead to the fact that the rubber is bursting. Silicone can stretch in such a way that you will not put it tightly and the cuff will behave, so act carefully. Move in a circle. If the tension is too difficult – you can apply a slightly dissolved detergent or washing powder on the clamp and the groove of the seal.
- Check that the cuff “sat down” to the inner clamp, did not fly away from his edge. Make sure that the drum does not hurt a gum – otherwise it will quickly erase it, and the same breakdown will again manifest itself.
- To put the internal clamp, using a configuration screw, set the optimal length of its circle. He must fully coincide with the groove of the cuff. Tighten the screw again.
- Insert the edge of the clamp near which the hook is located. The second edge of the clamp with the spring is put on it.
- Lock the clamp at the point of reference, Looking for a hole in the door of the door blocker. Hooking the spring for her hooks in the place of holders, tighten the clamp so that the spring is in its landing place.
- Install counterweight internal clamp and screw the bolts that kept them.
- Making sure the cuff is sitting exactly in its place, Install the dashboard back by twisting all the screws, including the one that was located near the drain pump. Return the pump cover and paste the top of the front panel where it was.
- Insert and slide the bottom of the front panel.
- Return to the location panel (with buttons) and set the tray to supply the washing powder.
- Pull the edges of the cuff and secure it on the case.
- Install the outer clamp on your place, Check the starting position of bolts and snacks.
Turn on SMA and select linen mode. To check whether there is no leakage, SMA during operation is allowed to tilt forward. Water will fully close the glass hatch and cuff over the entire length.
In case of explicit difficulties when changing any spare parts, including the cuff – better contact the service center. Calling the wizard to the house will solve this problem – if it is impossible to remove the old and fill a new cuff do it yourself.
The washing machine-machine of any company is even cheap Chinese – will serve quite a long time. But this is achieved only with timely care, including replacement of worn items to the same new. With a successful circumstance, the corporate technician is able to withstand the service life of 30 years instead of the stated several.
Replacing Cuff Luke Washing Machine Presented in Video Next.