Late water from under the washing machine are simply obliged to alert. As a rule, water is formed on the floor next to the washing device, and it came out exactly from it, then you should search and eliminate breakdown immediately. It should be borne in mind that the leaks can lead to more serious consequences in the form of flooding of neighbors and damage.
What to do first?
Modern producers of washing devices often equip their products with leakage protection system. This allows you to overlap the water supply to the machine when a malfunction has appeared that it will prevent flooding. The flows of water from the machine are rather common faults among many models of washing machinery.
If it became noticeable that the washing machine was proceeded, it is important not to enter into the resulting puddle or immediately start to wipe it. The first thing to do is turn off the device from the mains. While the machine remains included in the outlet, it is dangerous for the life of those who are near.
The second action, if the water flowed during washing, is the overlap of the crane through which the liquid from the water pipeline is supplied to the technique. To do this, just turn the desired crane in the closed position.
When both actions are made, you can merge the water that remains in the typewriter. This is possible with the help of an emergency drain pipe. It is a slot of a small length with a plug on the end, which is located behind a separate door near the drain filter.
If there is no emergency hose in the model, the water can always be lowered using the filter hole. It is located on the front panel. In the last stage, you must get all things from the drum. Only after all of the above actions can be searched for inspection and find out why washing machine flows.
Causes of malfunction
Most often, the washing unit proceeds if the rules of operation were violated. Often, water runs due to washing with means that are not suitable for this type of machine or washing mode. As well as Among the most common reasons, it is worth noting damage to the drain pump.
Several less often leaks occur as a result of defective parts or poor-quality assemblies of nodes.
Bulk or drain hose
Start searching the breakdown should be from the hoses for which the water flows and draining. It is important to inspect them throughout the length. Longitudinal cracks and most other damage visible immediately. They can form elementary when rearranging furniture. After all, under such circumstances, the hose can continue to bother or pull too much.
If the puddle next to the machine is formed when the water set, and the hoses seem to be integer, then they should check them more carefully. To do this, they must be disconnected from the device and put the plugs from one side. After that, along the entire length of the hose, it is necessary to wind toilet paper and fill it with water. If the hose passes somewhere, then the wet traces come on paper.
Also, problems may arise due to the poor compound of the filling hose and fitting. If the checks of the hoses showed that they are completely integer, then they should be carefully connected with a washing device.
If the machine flowed, but slower (for example, water just drips), then you should look for the reason in the tray for washingal. In the process of washing the substance from it is washed out with water. but Sometimes powder or other substance can remain due to incomplete dissolution in the tray and turns out. In this case, water does not pass quickly through the dispenser, so some part of it falls out.
If, when inspected in the tray, almost all holes were clogged, the reason for the waterproof water is here.
The dumping nozzle can cause the machine. This occurs as a result of the influence of the vibration of the unit during the rotation of the drum. Most often, this leads to the fact that the place of connection of the filling nozzle with a tank loosens or even collapses.
The bay valve pipe can also leak if its integrity or tightness of the compounds is broken. You can see it after removing the top cover from the washing device. It is under it that is this detail.
After several months from the beginning of the operation of the washing machine, it is possible to flow a drain pipe. This happens either due to excessive vibration of the washing machine, the destructive joint, or as a result of a poor-quality pump connection with a tank.
The fault will be able to detect and eliminate if you can enclose the washing device so that you can get to the drain path, which is located at the bottom of the machine from the back of the back wall (put horizontally support).
The negligent use of the washing unit can lead to the failure of the cuff on the door of the hatch. Especially it will be good will be visible when rinsing or annealing, as it will flow from under the door of the machine. Leakage is possible even with minor damage cuffs.
When drumming the tank, the washing device flows below. Such The most important element of the design may fail only because of the improper operation of the aggregate. You can reveal the breakdown, if you put the machine side, and then carefully examine her bottom. Preferably to highlight the flashlight. Place of damage will be seen in the footsteps.In addition to cracks in the plastic part of the tank, the flow may occur due to a faulty rubber gasket connecting it.
In any case, about the faulty tank, it is best to get advice from professionals.
Deformation of Salnik
Another detail of the washing machine, which is often the cause of the fact that water is pouring to the floor, can become a gland. This element protects bearings from water from entering them. With a long service, the seal loses elasticity, deforming, appear to be disliked. Liquid in these cases penetrates bearings, and through them and outward devices.
How to eliminate?
Knowing the cause of the leaks of the washing device, often it can be eliminated independently. For example, If the problem is in the drain hose, then such a malfunction can be temporarily eliminated by using the most ordinary insulating tape itself. In the drain system, the fluid pressure is quite small, so the damage is discounted, the damage will allow you to make a couple of styrics. However, in the end you will have to buy a new hose and change the progressive.
As for the tested hoses and nozzles located inside the device, they will only need a complete replacement. But if the reason for the connections, then the flow is pretty simple. It is enough to miss the place of connection with rubber glue and wait for it to complete drying (about 20 minutes). But at the time of drying, it is advisable to tightly compress the connection site.
The drain filter also changes easily. Need to unscrew it from the neck. After that, make inspection of the thread and make sure there is no dirt and dried salt sediments on it. After cleaning, install a new filter and thoroughly tighten the lid so that it fit as close as possible.
Machine door leaks testifies to cuff damage. Minor cracks in it can be repaired using waterproof glue and elastic patch. To do this, you need to remove the seal, first I reset the clamp, holding it in the hole. When installing the restored cuffs, it is advisable to make it to be on top of the hatch. So the load on it will be minimal.
If this repair did not bring results, you should put a new cuff. It is quite difficult, so it is better to use the help of a specialist.
Metal tank consists of two parts, between which there is a rubber gasket. If the malfunction in it, then the gasket changes to the new. When cracks are detected in plastic, they are eliminated using polyurethane sealant. Of course, if they are large or located in places, which are difficult to get, it will be necessary to disassemble the washing unit. However, the leak from the tank is better to entrust to eliminate professionals, since the problem may be more global, up to replacement of the tank. Sometimes it is more profitable to buy a new washing unit than to make a replacement of the tank.
If water leaks due to worn out salts, it will have to change the bearings, because the wear of these parts leads to the fact that water begins to leak through the bearing assembly. To eliminate, you need to remove the back cover, get old bearings with the glands and install new.
It should be clarified that the scale formed on the BEEN in the washing device cannot cause leak. This is possible only in cases where the heating element explodes and burns the tank. However, this happens quite rarely.
Practice shows that with any problem you can cope if not on your own, then with the help of specialists. It is important to remember that the fault response must be very fast. Otherwise, a small breakdown can lead to more serious consequences.
Household appliances require proper operation, otherwise its service life is significantly reduced. There are a number of recommendations that should be followed in order to avoid the flow. For example, before loading clothes in the drum, it is important to examine it for metal elements. If such is, it is necessary to wash things in a special fabric bag. Similarly, it is necessary to act with small things that can get into the drain nozzle of the aggregate.
Before closing the main cover of the washing machine, it is necessary to check how tightly the drum is closed. This is important for models that have vertical load. This advice will prevent water emissions out in press mode.
Besides, At the end of the washing, we should not forget to turn off the washing machine from the mains. This is due to the fact that voltage jumps are capable of damage. Install the machine is best in places where the humidity is the lowest. For example, a good place for a washing device will be a kitchen.
So that the service life of the machine was long, do not overload it with things. Overload can lead to leaks in press mode. Popular water in the water supply line also causes damage. Therefore, it is better to install a filter in advance. And also to avoid leaks, it is important to use exceptionally high-quality washing products.
To avoid tank faults, you carefully check all pockets before bookmarking into it. It is especially important to check children’s and workwear, where they may be sharp or metal objects.
It is not worth a long time to leave the washing unit without work. It should be clarified that downtime has a negative impact on rubber parts, worsening their elasticity and strength. Often, when washing after idlers, leaks are formed. Periodic cleansing of a drain tube can save. It can be buttons, pins, coins, studs, toothpicks, “bones” of bras.
About the reasons for the leakage of the washing machine See below.