How to fix or replace the pump in the Bosch washing machine?

By performing the task of the primary assistant in household matters, the washing machine turns into an indispensable household appliances. Her breakdown brings a lot of discomfort. The appearance of signals of a problem in the form of a program failure during washing in the main mass is associated with the functioning of the drain system.

In the washing unit, the pump is capable of scoring, which is necessary in the shortest time to clean. Otherwise it will be necessary to eliminate a more solid problem, which it can lead to.

How to fix or replace the pump in the Bosch washing machine?

How to fix or replace the pump in the Bosch washing machine?

How to fix or replace the pump in the Bosch washing machine?

How to remove?

If, when washing, the display shows the error “Pump clogged”, in order to clean it, it is necessary to make disassembly. Perform the following actions.

  1. Remove the top and rear casing of the washing machine By means of a hex screwdriver.
  2. After that It is necessary to put the machine side, only pre-fix the drum inside the washing machine. A piece of cardboard or something like that. Just put it between the drum and the sidebar of the case so that when turning the drum, it has not in contact with the panel. This will allow to progress from mechanical damage to the internal elements.
  3. Now disconnect the electric pipe, we scroll the pump against the progress of the clock arrows and the extraction. There is an opportunity to face difficulty – on separate modifications of Bosch washing machines there is a clamp that prevents the dismantling of the pump. It is not necessary to shoot. Through pliers, move it away from the pump. After that remove the pump. Be prepared for the fact that a minor amount of fluid may be on you.

How to fix or replace the pump in the Bosch washing machine?

How to fix or replace the pump in the Bosch washing machine?

How to fix or replace the pump in the Bosch washing machine?

How to fix or replace the pump in the Bosch washing machine?

How to clean?

The pump cleaning operation is that in the pump you will need to very carefully clean one component – impeller. To fully clean the impeller, It will also be necessary to remove it.

The process of removable impeller is easy: Through a screwdriver, you must unscrew the screws that connect 2 parts of the pump. When these parts are disconnected, you will see a small head. It will be an impeller. When the unit is working, this head rotates, thereby draining water.

How to fix or replace the pump in the Bosch washing machine?

How to fix or replace the pump in the Bosch washing machine?

How to fix or replace the pump in the Bosch washing machine?

Clean it from dirt, fibers of wool, hair, thread and the rest of the garbage and wipe the inner snail element. At the end of the event, collect a pump, install it in place, also assemble and how to secure other removed items. When the device is finally collected, perform the test washing. If the water is in accordance with the norm to fill and merge, and during the operation of the device there will be no knocks and noise – therefore, you did everything right.

Do not forget about the filter. Not every time the cause of water failure is specifically a pump. The car can refuse water Due to the clogged plum filter.

Clean the filter of the washing machine pump can be in the process of dismantling the pump, because getting to this element, you will still remove the filter plug. Simply immediately pull out all the garbage from it and foreign objects, and then remove the pump itself.

How to fix or replace the pump in the Bosch washing machine?

How to fix or replace the pump in the Bosch washing machine?

How to fix or replace the pump in the Bosch washing machine?

How and how to replace?

Replacing POMPH in Bosch washing units varies with the rotation of drain pumps in Samsung washing machines or LG only by extracting it. And in particular – not through the bottom, but by dismantling the front wall.

So, proceed.

  1. Primarily It is required to disable the unit from the electrical network, unscrew the pump filter and release the drain system from the liquid. Then we take a screwdriver, we find the hatch of the hatch under the ring seal (the iron ring with the spring should be installed), we draw it and carefully dismantle it.
  2. After removing the clamp, disconnect the ring seal, and so that it does not interfere, it can be pushed into the tank. Now it is necessary to dismantle the upper part, unscrewing on the reverse side of the 2 screw housing and push it back to the limit.
  3. Putting the central stopper, pull the tray for detergents.
  4. Unscrew the screws from the control panel. It is fixed from above, through the latch. We dismantle and remove it on the side (up), you do not need to disconnect the electric pipe.
  5. Under the opened hatch of the filter of the drain system, you will find the screw, which holds the bottom of the trim. Turn it out and shift plastic to the left side until it clicks. Then we dismantle the panel, and 2 screws fastening the front wall become available.
  6. After unscrewing the screws, pull the front wall on yourself and up, and disconnect it. Disconnect all electrical hardware and connectors on the front panel, including a hatch lock device. Facial wall put on the side.
  7. Now you can go to the dismantling of the drain device from the body of the machine. First of all, it is necessary to dismantle from the snail nozzles, squeezing the spring of the clutches by the poles. Initially, the nozzle is dismantled, stretched from the drum, and then the plum pipe.
  8. Disconnect the wire feed on the pump. Now it is necessary to turn the screws that hold the snail with a drain filter.
  9. We take a pump with a snail from the machine hull. Press the screwdriver to the retainer and turn the pump relative to the snail until it is separated. On a note! Before removing the snail, apply via the marker noted, so as not to forget the initial location of the excavated elements for further unmistakable assembly.
  10. Connect a new pump and snail. Install the new drain pump in the landing place can be very pressing on it and tugging the clock arrow. Do not forget to return the clip to your place, connect the wiring and carry out a revolving assembly.

How to fix or replace the pump in the Bosch washing machine?

How to fix or replace the pump in the Bosch washing machine?

How to fix or replace the pump in the Bosch washing machine?

Immediately, how to put a pump in place and connect all the nozzles, test the connection on the leakage. To do this, fill in the drum some water. If connections are dense, you can continue assembly work. This is completed on this.

Remember! When rotating a drain pump, it is required to select an absolute analogue of the design and technical characteristics. All drain pumps differ both in terms of power and productivity and according to the method of fixation. It is necessary to choose only in reliable and deserved a good reputation for manufacturers.

How to fix or replace the pump in the Bosch washing machine?

How to fix or replace the pump in the Bosch washing machine?

How to fix or replace the pump in the Bosch washing machine?

About how to replace the drain pump (POMPU) in the Bosch washing machine, look next.

Rate article
( No ratings yet )
Share to friends
Rebuildhom.info - construction and repair, dacha plot, apartment and country house, useful tips and photos
Add a comment