How to put the corners?

The formation of smooth internal and outer angles is a very important point when conducting finishing works. Properly decorated angles attach a neat appearance and emphasize the geometry of space. With strict observance of the finishing technology and competent selection of consumables, the process of self-tapping will not cause difficulties.

How to put the corners?

Selection of material

In the modern market for construction and finishing materials, the shplanies are presented in a wide range. Their compositions differ among themselves for the purpose, properties and time of viability.

Before you start buying a material, you need to familiarize yourself with some characteristics of each type:

  • Polymer putty is a finishing coating and is used at the end of the finishing work. The mixture aligns the surface of the wall and has high moisture resistance;
  • Gypsum is allowed to use only in closed rooms. Forms a smooth surface, quickly solidifies and dries;
  • Cement putty is characterized by high moisture-resistant qualities and can be used when finishing bathrooms and kitchens. The disadvantage of this species is the probability of cracking after drying. To prevent the appearance of cracks, the surface should be periodically moistened until the inner layer is completely dry.

How to put the corners?

How to put the corners?

How to put the corners?

At the form of the release of the shtclowing there are dry, requiring independent preparation, and ready. For purpose, specialized, leveling, finishing, decorative and universal solutions are distinguished. The choice of material is carried out individually and depends on the type of work performed and the degree of exposure to external factors.

You should also purchase primer. To form both external and internal angles, it is recommended to use deep penetration solutions. This will provide good grip with a wall with a wall and prevent detachal of the plaster.

How to put the corners?

How to put the corners?

From the tools you need to prepare three spatulas: two straight widths 25 and 10 cm, and angular. To obtain a homogeneous solution when using dry mixtures, you will need a paddle nozzle on a drill or a building mixer. As an equalizer of the surface, you can use a grinding grater with a mounted sandpaper or grid, and in the preparation of the surface under the adhesive of the wallpaper, it is better to use abrasive with a degree of grain degree R100 – P120.

To strengthen the outer angles, you should purchase perforated corners, and for the formation of the internal – sulfyan grid.

How to put the corners?

How to put the corners?

Technology of work

The first stage should be a visual inspection of the corner surface and removing explicit protrusions using a building knife. Then you should check the vertical of the walls using the level and pencil note the strong deviations. Next, both walls are primed at a distance of 30 cm from the angle. After that, you need to impose the necessary layer of putty in places with pronounced depressions and chips.

The thickness of the layer should be small, so if necessary, it is better to apply a few thin layers.

The next stage will be the applying of a layer of the shtaplanka on the surface of the walls adjacent to the corner from top to bottom and installation in the newly superimposed solution of a metal or plastic corner with perforated side. Excess the solution that will be released through the holes of the corner must be removed using a narrow spatula.

When using a plastic model, it is important not to confuse it with an overwhelming corner, which has enough thick sides and does not fit. The advantage of plastic overlays over metal is the impossibility of their oxidation, corrosion and destruction.

How to put the corners?

How to put the corners?

How to put the corners?

Next, the perforated corner must be set on the level and add a solution to it where it is necessary. After the shplanke grabs, you can start to put the adjacent walls. The solution is applied alternately on both surfaces at a distance of 25-30 centimeters from the angle and spatula spatula. Excess mixtures are removed by a narrow spatula. The thickness of the applied putty should be sufficient for the perforated lining when grinding does not barney.

If the wallpaper is not planned, the chamfer on the junction can be removed. This will prevent the subsequent chipping, but will slightly reduce the attractiveness of the angle.

After drying, the solution can be proceeded to grinding the angle and the subsequent primer surface. Then the finish shtackel is applied, which is also neatly grinding after drying. If, after applying the finish solution, some flaws were discovered, they should be touched, let’s passion and get off. At the end, the surface is blocked once again, after which it becomes ready for finishing decorative trim.

It should be remembered that the formation of slopes with a perforated corner is possible when performing direct corners. For finishing beveled corners, the material does not apply.

How to put the corners?

How to put the corners?

Methods

In order to properly sharpen the inner corner, it is necessary to pre-hold a constructional carbon from the ceiling to the floor and mark all deviations with a pencil. The protrusions are cut by the plane, and the depressions are ground and shapled. After drying the solution, the surface of the walls forming the angle should be primed, and only after that, proceed to the putty.

The technology is to alternately align each of the walls with the application of the solution as close as possible to the corner. Excessive solutions are also removed alternately – first from one wall, then on the other. To make it easier for themselves to form an angle, you should use a special corner spatula, with which you can form a perfectly smooth junction. After applying the solution and the primary setting, it is necessary to perform the control measurement of the angle with the help of a construction kit. Revealed recesses will have to put out again, and irregularities will be removed during the subsequent grinding.

How to put the corners?

How to put the corners?

If the junction turned out to be slightly rounded, then the formation of a direct angle is achieved by grinding the emery canvas NO 150. Grinding the adjacent walls is also performed alternately until it is possible to remove the sharp and smooth inner edge.

When plasterboard corners of the walls of the walls should be installed the self-adhesive grid-schupan. Its width should be 5 cm. The sticker needs to be done very carefully, not allowing the inflection and skew material. Further, the works are manufactured by technology used for concrete grounds.

How to put the corners?

How to put the corners?

How to put the corners?

Complex forms

For spacing complex architectural structures and arches, it is recommended to use a plastic corner that bends in any directions and allows you to form smooth and beautiful corners. Before proceeding with the overlay of the putty, you need to visually inspect the surface and remove the protrusions using a planer or a building knife. During the trim of plasterboard structures, it is required to carry out a hand along the edge of the surface and check it for the presence of protruding screws. In case of detection of discovering hats, fasteners should be tightened.

How to put the corners?

How to put the corners?

How to put the corners?

Then the surface must be projected and let it dry. Next, measurements of the edge of the generated angle should be measured and measure the arched corner of the required length. It is necessary to cut off so that throughout the ribs there are no joints.

If for some reason, the cover is mounted, the docking ends of the corner should be fixed with foam glue and additionally fix with a construction stapler.

After fixing, the lining should be started with the shplotovka of figured bends. Start to output an angle with a curved surface and then move to flat. Important condition is the uniform application. Excessive thickness and inaccuracies in the formation of smooth transitions can be aligned with grinding, for which paper with labeling P120 is recommended. Next, the surface is dustd and stuffed.

How to put the corners?

How to put the corners?

Examples of execution

Clear compliance with installation technology and accuracy during work allows you to easily make repair with your own hands, saving time and without resorting to the services of specialists.

  • Finishing internal joint walls by an angular spatula.

How to put the corners?

  • Registration of the outer angle with a plastic corner.
  • Installing a metal perforated corner to an outer angle.
  • Preparation of curly corners to putty with overlays.

How to put the corners?

How to put the corners?

How to put the corners?

Tips for experts on the right shpocking angles See below.

Rate article
( No ratings yet )
Share to friends
Rebuildhom.info - construction and repair, dacha plot, apartment and country house, useful tips and photos
Add a comment