How to make a circular from the grinder do it yourself?

Almost every private building has an outbuilding room for economic purposes. It is most often stored building materials and tools, inventory and agricultural machinery.

This article will be discussed about how from the subwoofers left after repair, independently make a circular saw based on the engine from the Bulgarian.

How to make a circular from the grinder do it yourself?

How to make a circular from the grinder do it yourself?

Design features

Conduct work on the transformation of one type of saw to another with the use of old, remaining from the repair of elements. Possessing the locksmith skills and smelting, you do without much effort to handle this task.

Distinctive features of such a type of fixtures are that there are circular saws from the grinder as a homemade machine or manual fixture fixed on the table or another basis.

If you have an old Bulgarian, then the engine is best removed from it and use as the core of the future saw. The engine from the washing machine is also suitable.

How to make a circular from the grinder do it yourself?

How to make a circular from the grinder do it yourself?

Any circular has several main components:

  • homemade table as a sustainable frame;
  • Face for saw;
  • ENGINE MODE;
  • focus of sliding;
  • bar for adjusting the height of the cut;
  • Reducer, saw blade.

How to make a circular from the grinder do it yourself?

How to make a circular from the grinder do it yourself?

    Such a machine is suitable for cutting small wooden bars. When wood processing is planned in large quantities and large dimensions, it is better to purchase ready-made production equipment. Its value is great, however, for business, this purchase will be the perfect solution.

    To safely work on a circular saw, it is necessary to choose a special attention for it. Bulgarian is a complex tool and use a disk from it for cutting wooden products. At any time, it can occur.

    Rounding at very high speeds, such an element is able to open the tree into the chips from which injuries can be obtained. This is because when processing on disk is a high temperature load. It is best to purchase a new product specifically for circular saw.

    How to make a circular from the grinder do it yourself?

    How to make a circular from the grinder do it yourself?

    If the circular is fixed on the floor, then the framework should be fixed with fasteners (corners) to ensure its stability. For the manufacture of the bed, you can take an unnecessary cabinet or several sheets of chipboard. However make it very much from metal.

    The main working surface of the table top is better to perform from plywood or laminated wood chipboard. The table should stand very firmly on the floor so that his vibration was insignificant.

    The saw on the saw is installed smaller diameter, what used for the grinder – it will not give the engine to overheat. You can buy it both in auto parts stores and in specialized construction markets. The power of the bulgark engine from which the circular is made should not be less than 1600 W.

    A more complex option implies the installation of additional elements: pulleys, belt system. With this method of manufacture, homemade design will acquire a type of production machine. The presence of a belt will reduce the speed of the disk rotation.

    How to make a circular from the grinder do it yourself?

    How to make a circular from the grinder do it yourself?

    Required toolkit

    To work, you will need tools, building materials or pieces of parts for assembly details of old furniture.

    We will be needed:

    • pliers, screwdriver, adjustable keys, hammer;
    • metal sheet, corners, nuts, bolts, screws, fasteners;
    • Bulgarian and electric drill, switch and socket;
    • Sculpture, ruler.

    How to make a circular from the grinder do it yourself?

    How to make a circular from the grinder do it yourself?

    Step-by-step instruction

    The process of manufacturing a circular bar of the grinder includes a number of stages:

    • First of all, you need to make the base table;
    • Install the Bulgarian and Disc itself;
    • attach a stubborn bar;
    • Test electricity;
    • Check Start.

    The main element of both the mini-sample and the stationary version of the circular is the table-frame. You can make it using drawings, or to build to your taste, observing the basic principle of manufacturing such a part of the saw. Everything will depend on the size of the wood material, which is going to cut.

      We will tell about how to remake the grinder into a miniature circular. With it, you can cut the bars, small boards, rails used in repair or in private.

      How to make a circular from the grinder do it yourself?

      How to make a circular from the grinder do it yourself?

      The table looks in the form of a workbench, the foundation of which is most often done from the sawn timber.

      • Initially, the chipboard sheets are taken and a miniature table is narrowing from them, whose legs are performed at such a height so that Bulgarian placed under the face. Fasten them to ribs of rigidity. Those, in turn, are made of small boards and fixed on the edge of the table top at a distance of 7-10 cm from the bottom side using selflessness.
      • The upper work surface is preferably made from laminated plywood. When the tabletop (bed) is ready, it turns down the front side and conduct the markup to the installation of the grinder and the saw blade. Based the element from the Bulgarian, they make measurements for a slot to a new disk. At its ends, the extreme borders of the future opening (slots) are celebrated. Then take the drill and drill the formed points.

      How to make a circular from the grinder do it yourself?

      How to make a circular from the grinder do it yourself?

      • After that Using the ruler, the edges of the formed holes are connected, After spending two parallel lines on their width. Part of the table top inside such lines are cut with a grinder. Slotted.
      • Then You should purchase a new disc in the store. The optimal option will be the purchase of a sample for a 125 mm woodwork with carbide teeth – they can be 24, 36, 48.
      • Under the working surface of the table, the plank is screwed to which the grinder is fixed, Using clamps. You can fix it with the help of clamps made by yourself, and tightening nuts. At the same time in the table (in the cut opening) make the installation of the disc itself. It should be located so that most of it is on the surface. It is advisable to hold the protective visor attachment. It is sold in any construction store, so you can buy such an element without difficulty. It is usually attached to the loop, letting the visor’s opportunity to fade.

      How to make a circular from the grinder do it yourself?

      How to make a circular from the grinder do it yourself?

      • From a metal corner or from plastic trimming of an old plinth, a stubborn bar is made. It is possible to mount it on the Faneur or chipboard. In length, this plank must be the same as the working surface of the table. Screw the bar (limiter) for a distance of at least 2 cm from the teeth of the saw disk. At the ends of the rails make two holes and hold fixation in the table with the help of bolts or ordinary self-tapping screws.
      • The processed board or bar must fully fit on the tabletop, Because when driving at high speed sawdust, vibration is exposed to. It is impossible to keep the sawn timber on weight – there is a chance to get serious injuries.
      • At the next stage of work On the inside of the mini-table make the fastening of the electrical outlet, Through which the wire is allowed and then install the switch. Usually its fixation is carried out from the outside of one of the ribbon. The wire from the switch is directed to the power source – thus electricity is summarized to the circular.

      When I saw ready, make a check start and sawing small bars, paying attention to the speed of rotation of the disk.

      On this work is completed.

      How to make a circular from the grinder do it yourself?

      How to make a circular from the grinder do it yourself?

      Folk crafts, not to make a circular table, use vice as a support frame. At the very beginning, the Bulgarian clamp with a disc on the edge of the usual table, removing the protection and reloading the grinding handle. Then take a fane or chipboard for the formation of the bed, in which the hole is done under the disk. Fasten it by drilling holes, bolt is inserted into it. It must coincide with the hole on the grinder, where the handle is attached. Bolt is tightened until it stops using the key.

      Spring materials make a stubborn bar or limiter. Fasten it with bolts at the ends of the bed with the help of conventional screws. Under the weight of Bulgaria can bend forward and chain the disk of the tabletop itself. In this case, you need a handle. It can be turned out of the old twin key and screw in the grinder by making the engine backup.

      It works such a miniature homemade design clearly, the cuts of the rails and the BRUSEV produces qualitatively.

      How to make a circular from the grinder do it yourself?

      How to make a circular from the grinder do it yourself?

      Operating Rules

      Use when processing wood designs such as homemade saws, equipped with discs, imposes certain responsibilities on their owners.

      In addition to well-fixed on the floor and protective casing on the disk, it is necessary to organize the supply of sawmill material in both directions: right to left and back. Boards and rails Move on the bed during the operation of the circular can not be hand, for this you should use a bar or its analogue of wood. It is not recommended to be near the rotating disk at a distance of less than 25-30 cm. Can not be kept close to the saw – You can damage your fingers.

      You need to turn on and off the circular saw by means of a button located either on the side, or in front of the unit. When the disk rotates, then stand behind it or ahead is prohibited.

      How to make a circular from the grinder do it yourself?

      How to make a circular from the grinder do it yourself?

      Security measures

      In order to avoid getting into the eyes of small wood when sawing, as well as a chips, it is necessary to carry out work in glasses. It should be taken care that the sawing is performed in a well-lit room or a circular stood on an open to the sunny rays.

      When working with material for cutting, you need to ensure that there are no nails or large bitch in it. This circumstance can provoke a disk breakdown or a change in the direction of the moving bar or rail. At best, the engine can be spoiled, and the disk is blunting. In the worst version, the building material escaped from the hands will cause injury to someone who is engaged in sawing or people nearby.

      How to make a circular from the grinder do it yourself?

      How to make a circular from the grinder do it yourself?

      You can not turn on the circular saw with wet hands. It is strictly forbidden to carry out work in a drunken state. Cutting the sawn material can be removed from the working surface of the bed only when the cutting disk is completely stopped.

      Thus, to make a circular at home will be able to anyone who knows how to operate with construction tools and having the skills of making wooden or metal structures. You need to follow the rules of operation of the aggregate. Such a saw in the future will become your assistant and will significantly reduce the labor costs for the processing of sawn timber used in the personal economy.

      About how to make a circular from the grinder with their own hands, see the following video.

      Rate article
      ( No ratings yet )
      Share to friends
      Rebuildhom.info - construction and repair, dacha plot, apartment and country house, useful tips and photos
      Add a comment