How to install a threaded rivet?

The nipper is a very peculiar way of unsolved fasteners. One of its indisputable advantages is low cost. In addition, such a mount avoids excessive deformation of blanks, does not cause changes in their physical or chemical properties, as it eliminates the heating, allows you to connect the details of various nature. In this article, let’s talk about the installation of so-called threaded rivets.

How to install a threaded rivet?

How to install a threaded rivet?

What do you need?

Threaded cooling on its device is somewhat different from the same widespread exhaust ripples. The main part of the other type of consumables is the fmined metal sleeve – quite similar. But in the case of threaded ripples, the exhaust rod is missing, its role is played by a special threaded nozzle on the tire.

After installing such a fastener at the site of fastening design details, a reinforced metal threaded slot remains where the bolt or screw can be inserted with an appropriate thread step, which can not only turn the nut, but also fasten the bracket, corner or any other structural element. It distinguishes threaded consumables from exhaust.

To install such fasteners, you will need:

  • The consumility itself is a nipper;
  • drill;
  • drill with a diameter of 0.1 mm larger diameter;
  • Skloper for threaded ripples.

Of course, a roulette can be needed for marking, sometimes if the material requires, Kern.

How to install a threaded rivet?

How to install a threaded rivet?

How to install a threaded rivet?

How to install a threaded rivet?

If there is no crook, but you only need a few threaded claps, buy it, of course, not necessarily. Craftsmen recommend making a device for installing screw row on their own. Of course, do it without, albeit small, set of materials and tools is impossible.

But if the reserve of all sorts of bolts, nuts and other techniques is available, try to choose the components for the homemade ribbonally quite real.

For such a homemade tool, you will need:

  • Long bolt with a thread pitch is the same as the clap;
  • two washers with an inner diameter corresponding to the diameter of the bolt;
  • Larger diameter nut sleeve;
  • Nut that can be screwed at the bolt.

It is quite nice if the main working elements – bolt and nut – are made of more hard steel. This will repeat the reliability and durability of the homemade ribula.

How to install a threaded rivet?

How to install a threaded rivet?

This, of course, is not a mandatory set, you can try to assemble a device from other components. And if there is a welding machine, you can build a tool with reinforced handles that reduce efforts and improve reliability of homemade.

Step-by-step instruction

If there is a crook, it needs to be configured to the appropriate nickel nut, adjust the threaded rod in accordance with the closed length. If all adjustments are correct, step-by-step instructions for installing a threaded rumble looks in general, as follows:

  • Connect details or design elements as required;
  • Knowing the diameter of the clap, select the drill by 0.1 mm of larger diameter;
  • drill the blank, trying to withstand perpendicular;
  • Having a ripple knot on the rod;
  • carry out the installation of the compound, pulling the threaded rod using the knob;
  • To unscrew the rivet.

How to install a threaded rivet?

That’s all, Fastening with a screw rope carried out. If necessary, you can strengthen the connection with a bolt and nut or install any other design element using a bolt, since threaded mount appeared on the surface.

How to install a threaded rivet?

Fasten the threaded jam, using a homemade device, quite real.

It is important to remember: if the bolt has a small hardness of steel, it will not be able to plump repeatedly with it. Even with very careful use, it is unlikely to be able to install more than 5 pieces. Either thread will be reduced, or the bolt should be.

If the device is collected from those elements that are given above, in general terms, it is worth it with a rush with it as follows:

  • Drill the mounting hole with a diameter of 0.1 mm larger diameter;
  • Collect homemade creek: Having a long bolt with a thread that corresponds to the thread of the consumor, the nut, to put the washer on it, then install the sleeve, which is also covered with a washer;
  • shut a rush to the end of the bolt;
  • turning the nut to ensure that the sleeve is stuck through the puck in the cute head;
  • Insert a rumble into the prepared hole;
  • Holding the bolt from turning with a wrench, to turn the nut to another key so as to pull the bolt and deform the ripper;
  • when turning will be hard, unscrew the bolt.

How to install a threaded rivet?

How to install a threaded rivet?

How to install a threaded rivet?

How to install a threaded rivet?

How to install a threaded rivet?

If necessary, you can strengthen the connection with the help of a bolt and nut.

It is clear that homemade structures for installing a threaded clutch made by different masters in different conditions from different components can be somewhat different.

The main thing remains one: it is necessary to pull the sleeve so that the rolling. Some homemade ribalists are supplied with reinforced steel handles, allowing to exclude from the crop process rather uncomfortable wrench keys.

      An additional element of the design of the self-made device for flipping by threaded consumables may be a small bearing, which allows to concentrate the force on the operation itself, reducing excessive friction.

      How to install a threaded rivet?

      How to install a threaded rivet?

      Recommendations

      The use of threaded ripples has its subtleties.

      • One of the most important conditions for the successful installation of threaded or wrench clamps is the correspondence of the diameters of the consumage and the mounting hole in the workpiece, otherwise turning may occur. Install such a row much more difficult. It is important to choose a drill with a diameter of no more than 0.1 mm larger diameter.
      • To avoid turning into the hole, it is better to pick up ripples having a longitudinal bowl at the upper part – they are tight thanks to friction.
      • When drilling holes in blanks, you can use clamp or vice to avoid displacement of parts. Otherwise the high-quality connection will not succeed.
      • Selecting the material for the self-made device for installing threaded consumables, it is important to take into account the effort that will experience the rod (bolt). It is better to refrain from setting a large number of steel grades of large diameter.
      • The most reliable connection is provided by hexagon crosses, but it is very difficult for them to prepare the landing hole. Better such consumables apply for installation of fine material products.
      • The manufacture of a self-made device for Clopping is justified only when performing a small amount of work. If you plan to install several dozen, and even more than hundreds of claps, it is simply necessary to acquire a high-quality creek.
      • For the home workshop, the most preferred can be considered a manual rivest; If an industrial scale is planned, electrical or pneumatic equipment is justified.

      About how to set a rivet without a rivet, look in the following video.

      Rate article
      ( No ratings yet )
      Share to friends
      Rebuildhom.info - construction and repair, dacha plot, apartment and country house, useful tips and photos
      Add a comment