All about blacksmithing vice

Peculiarities

Blacksmithing – a lesson, which is always surrounded by a certain glory and respect. But going to do it should be learned to study the future scope of activity. It is especially important to know everything about Blacksmithing Tiska.

All about blacksmithing vice

All about blacksmithing vice

First you should figure out what blacksmithing vice are and what they represent themselves. Like a similar device used in domestic work, in the locksmith and carpentry workshops, They are designed to hardly fix one or another item. It significantly increases the possibilities of processing billets in various ways. They can be calmly drilled, saw, strict, grind, and so on, without fear that the semi-finished product will move from the spot. Specifically, blacksmiths use vice for:

  • bending;
  • twisting;
  • disembarking.

All about blacksmithing vice

Special difficulties of the design from blacksmithing vice do not have to wait. But at the same time they have certain differences from those who enjoy the joiners and locks. So, completely unacceptable joinery vice, which are most often made of wood. And even ordinary metal will not fit – Be sure to need products from heat-resistant alloys. Usually, vice perform their task due to the pair of plates, disposed of mutually parallel.

The locking mechanism helps adjust the force of pressed. A special block is provided, with which a fast manual adjustment is performed. One of the plates is fixed as hard as possible, and the other can move. It is also worth noting that Blacksmith vice is usually heavier and externally gross than those used in more “thin” industries.

All about blacksmithing vice

Varieties

In the blacksmith can be found, we note, and the most ordinary plumbing vice. Just because there are also separate locksmiths. Such a tool is suitable for a huge number of tasks. Allocate:

  • small;
  • medium;
  • Large plumbing vice.

Their parameters are as follows:

  • Length – 0.29, 0.372 and 0.458 m;
  • height – 0.14, 0.18 and 0.22 m;
  • Sponge height – 0.05, 0.07, 0.09 m;
  • Sponge stroke – 8, 12.5, 16 cm;
  • Mass – 8, 14 and 27 kg.

All about blacksmithing vice

But it is worth it in mind that In individual models, the sizes can be much larger than that of standard samples. The classic version of the tisk – T-250 – in length it already reaches 66.8 cm. Their mass is 60 kg. Sponges perform 0.125 m. The width of these sponges is 0.25 m.

Otherwise, things are with challenges. The scatter of their mass is from 13 to 19 kg. Mobile sponge can move by 0.12-0.16 m. The length of the pussies is 0.37-0.4 m. Their width is 0.18-0.2 m, and exactly the same height.

All about blacksmithing vice

Concerning ordinary manual vice, then their length varies from 0.022 to 0.09 m. The width can reach 0.006-0.045 m, and the height is 10-15 cm. An important role is played by the compression force that vice is able to develop. It is determined by engineers by this effort, which will still move the hard blocked workpiece. At locksmiths, the force of compression varies from 15 to 55 kN, and the challers this figure is 20-30 kN.

Separately, it is worth saying about Parallel vice. They divide in turn on the turning and non-turning group. The name suggests that the movement of sponges occurs in parallel to each other, which allows you to get away from a number of weaknesses characteristic of the challenge structure. In the lower part of the rotary device there is a circle that is rigidly attached to the workbench or other support.

You can move vice in this circle to any angle, and then they are easily fixed in the selected arbitrary position.

All about blacksmithing vice

It is useful to consider I Graduation of vice in accordance with GOST 1975. It covers all models, the width of sponges of which is not less than 0.063 and not more than 0.2 m. Standard highlights devices:

  • general profile;
  • with a swivel sponge;
  • with 1 or several additional sponges;
  • with an acceleration of idling or at normal idling speed.

All about blacksmithing vice

All about blacksmithing vice

Recommendations for choosing

Even in an advanced blacksmith workshop must be at least some kind of plumbing Middle Dimensional Group.They successfully fulfill the majority of household tasks. Important: Powder metal products are not suitable. It is better to navigate on models, cast from steel or cast iron. For professional use in full, it is desirable to use an eccentric or quick-disconnect device.

Increased strength have steel vice with anvil. They make it possible to process workpieces with additional blows for a long time. It is useful to check whether the lining on sponges are removed. Sponge opening distance – another moment, which is fundamentally important for professional work. This property determines which details can be fixed in the vice.

All about blacksmithing vice

Visiting the store, you need to watch carefully, does the device look good.

Important: It is worth trying it in action. High-quality tool should not eat or move too fast and easy.

The running screw is normally supplied with a prevention mechanism, otherwise the design will be unreliable. When the sponges are closer, the discrepancy of adjacent surfaces can be not more than 0.5 mm.

All about blacksmithing vice

Broadening around the edges do not have to give a chassis to go somewhere or stick, that is, their diameter should be significantly less. When the lining is removed from the sponges, a good tool is not lost with parallel. Attentive inspection and careful climb will be allowed to detect whether there are no cracks in the bed. Of course, vice follows Check more on various backlash, and go for the purchase best in proven places.

All about blacksmiths for artistic forging See next video.

Rate article
( No ratings yet )
Share to friends
Rebuildhom.info - construction and repair, dacha plot, apartment and country house, useful tips and photos
Add a comment