How to power the LED ribbon?

Know how to power the LED ribbon, it is necessary to all who decided to buy similar lighting devices. It is necessary to figure out how you can feed the LED tapes 220 and 12 volts at home. And it should also be found out how to power the diode tape by batteries, and what other ways to feed the current can be used.

How to power the LED ribbon?

How to power the LED ribbon?

How to connect with an electrical network?

Connecting tapes with LED elements to 220 volt household power grids can be made in two ways. We are talking about missing and connecting techniques. Solder turns out to be significantly cheaper and more accurately more reliable than installing connectors. But but the connecting elements is substantially simpler. If the tape is calculated on 1 color of the glow, the connecting nodes must have 2 fasteners; Colored lamps are compatible with 4-finite products.

Connectors are needed primarily where the soldering is impossible, or if necessary, bend the LED tape at a certain angle. However, experts emphasize that it is better to always use the soldering iron of a proven sample. The soldering iron must have a latter comparatively sting. Accurate temperature adjustment is very important. Additionally, you will need:

  • rosin;

  • solder;

  • Scotch bilateral sample;

  • heat-shrink tubing;

  • Power supplies;

  • high-quality wires for connecting the tape to the power supply and connecting it with the power grid itself;

  • Sometimes – switch or socket.

How to power the LED ribbon?

How to power the LED ribbon?

How to power the LED ribbon?

Difficulties to work with the soldering iron quite overcome. On the working surface and around it should not be any easily lighting items. This surface must be solid and perfectly flat; then pick up a soldering iron and prepare it. It is advisable to clean the instrument. For this apply emery or metal brush. Pollution remaining after such processing can be removed if you need rags or sponges.

Bilateral Scotch is called to clamp a tape so as to eliminate its chaotic movement. But sometimes apply other retention solutions. IMPORTANT: It is impossible to use vice – they can damage the tape. Wires clean and remove isolation. Before it cut the tape at a certain point; There in production make a note with the image of scissors.

Accession is possible only with strict polarity observance. Then clean the contacts on the tape, some solder are applied to open spaces. Cables should be soldered in a pair of places. These places bend at right angles on various sides.

How to power the LED ribbon?

How to power the LED ribbon?

The soldering place is isolated by a special heat shrinking tube; Kanifold should not be cleaned.

Connection to 220 volts is possible exclusively using the power supply. The simplest option is the wire that replaces the diode bridge. If the tape size is more than 5 m, the connection must go strictly parallel. Refusal of the power supply often provokes the accelerated output of parts of communication in order. Harmful flickering is also inevitable.

But the benefit from the power supply is still one moment. Its use allows you to connect the entire contour. No more need to stretch the wires to each luminous segment separately. It is easier, and more reliable, and even aesthetically (no bunch of twisted wires). The main basic requirement is the calculation of the power supply to the necessary parameters.

How to power the LED ribbon?

How to power the LED ribbon?

How to feed with batteries?

If you need to use LED tape by 12 volts at home, and the total length of communication does not exceed 20 meters, then it is permissible to use batteries. This method is not too different from connecting to a conventional power grid. 12 volt supply voltage is an incomplete value; if it is more, you can not use batteries. You can use the “Tablet” or a meager battery. Sequence of steps:

  • solid stripping of contacts;

  • Running the tips;

  • processing flux;

  • attack of a black wire to minus, red – to the advantage of the pole;

  • A similar procedure is to connect to beds or buttons (however, a single wire is driven through them, which is connected to the inputs of the togglers, the exit must be allowed to be let the ribbon).

How to power the LED ribbon?

How to power the LED ribbon?

What else can be powered?

But sometimes connect the LED ribbon to the usual network or batteries is useless, or difficult, or impossible. In tourist, hunting, fishing practice, the most practical use of batteries. Any battle is suitable for 2-100 Ah. However, you will need to connect special connections. How to do it, write in the instructions for batteries.

At home is suitable for connecting to computers, laptops. In this case, you need to know both the electrics and the electronics. Usually take the yellow wire from the power supply. Black grounding wire is also needed anyway.

How to power the LED ribbon?

How to power the LED ribbon?

All areas connected to power supplies must be equipped with NSHVI tips so that the docking is as reliable as possible; Private craftsmen use pliers for their installation, and electricians – specialized tools.

How to power the LED tape, look in the video below.

Rate article
( No ratings yet )
Share to friends
Rebuildhom.info - construction and repair, dacha plot, apartment and country house, useful tips and photos
Add a comment