Types of peg for garter tomatoes and their use

Tomatoes are one of the most popular species of vegetables grown in our country. Tomato gained greater fame due to its taste, nutritious, dietary characteristics, as well as high yields in a wide variety of climatic conditions and a large species diversity. However, in order to achieve a large harvest, tomatoes require good care, including tapping to spicks.

Description and Functions

Tomatoes can be grown in a greenhouse or in the open soil, they are cultivated in a horizontal or vertical position. The method of vertical cultivation is considered more common. It allows:

  • It is more efficient to use the sowing square, growing a large number of plants in a small plot;
  • Get a better harvest due to good light illumination throughout the height of the bush;
  • Significantly simplify the process of watering, feeding bushes, as well as subsequent harvest;
  • Prevent damage to fruits when processing.

In suspended state, fruits during maturation are located above the ground level. It protects them from attacks of slugs and other pests, reduces the risk of fungal infections.

The most popular way of closing the tomato bushes is their fixation to vertically established backups – spicy.

What are the stakes come from?

In order to make pegs, you can use a variety of materials, including workflowers – metal fittings, plastic or fiberglass pipes, as well as shrub trunks and trees branches. And of course, the rope will need to perform the garter. Each material has its own characteristics, let us dwell on them.


Wooden supports are highly valued for their cheapness and accessibility. The service life of such pegs reaches 10 or more. Vegetable breeding can buy supports in the store – bamboo models are very popular. Some dackets make them alone from the remedies:

  • durable trunks of wild shrubs;
  • Stakenists from the fence;
  • Cherenkov from old shovel.

Depending on the tallness of the variety, sticks from 1 to 2 m long use.


A successful solution will be the use of metal rods. Durable and durable details are very convenient to insert into the substrate and get after the end of the season. Metal is distinguished by a strength, durability and reliability. It does not break, does not rot, and it is also withstanding the maximum wind and weight loads.

The only flaw – this is the high cost of new rods, so it is most often replaced by a redemption. Typically, the remains of pipes or fittings from repair and construction work.

Any bars with a diameter of 5-10 mm are suitable as pegs, and chosen height, focusing on the length of the grown variety.


Fiberglass is a composite based on metal and glass, it gives the material a special strength. That is why pegs for tomatoes from fiberglass reinforcement will become an excellent choice for garter growing bushes. The advantages of fiberglass are obvious: it is not corrosion, it does not break, not bend under the severity of tomato bushes, and in addition, it is distinguished by resistance to chemical triggers.

For work, pipes and columns with a diameter of up to 10 mm are selected, they are cut into separate elements of 1.5-1.7 m – this is a universal length for bushes of all varieties.


Plastic garden pegs can be purchased in any agromagazines. They are easy to operate, and also look very carefully on the beds.

For maximum reliability, preference is better to give plastic tubes with a metal rod inside.

How to make it yourself?

If you wish, you can make wooden backups for tomatoes with your own hands, without having special skills of work and special tools. To do this, you should prepare a wooden board with a length of 2-2.5 m, 10-15 cm wide and a thickness of 6-7 cm. It must be preloaded along the length and width on the required number of stakes, and then with a disk or hand saw, dissolve the workpiece into separate bars.

After that, it will remain only to perform grinding on the branches, and if there is no tool at hand – a coarse-grained emery. To facilitate the subsequent plug, the end of the stakes can be accepted at an angle of 45 degrees on one side of the backup or several.

In the manufacture of pegs from branches with them you need to pre-remove the bark and stern to remove all roughness. The location of the cut is preferably handled the resin to prevent the appearance of the roots. To increase the durability, the stakes must be slightly burning in the furnace or on the fire.

How to properly tapping tomatoes?

Tie a bush of tomatoes to the spicks is not at all difficult. The whole procedure is reduced to the fact that the support is fixed near the plant and the plant is tested for it. Nevertheless, in vegetable practice, a number of rules have been developed, the observance of which will make a garter as as gentle as possible for plants.

So, the optimal sizes of pegs are installed:

  • For tall grades, it is 2-2.5 m;
  • For the average varieties need shorter supports 1.5 m long.

The peg must be immersed in the ground by 50-80 cm. Located over the soil part of the support should exceed the maximum height of the bush at least 20-30 cm.

Checks should be placed on a distance of 10-15 cm from the stem from the northern or south side so as not to shade the bush.

If the land is rigid, then you need to score pegs with a sledgehammer or heavy hammer. If the substrate is loose – it is enough just to press on the support with hands, so that it goes to the necessary depth.

Take the Tomatoes to the Support can be used with the help of a beef of the material resistant to rotting. First, the rope is fixed on the support, only after that picked up the stem and binds it into several knots. To fix it is reliable, it is desirable to grab the stem, as well as a couple of neighboring brushes.

Everything that the gardener remains is only periodically to recoup the tomato as the bush grows, for this tape, from time to time, move up.

See tips on the use of pegs for tomatoes.

Rate the article
( No ratings yet )
Add comments

;-) :| :x :twisted: :smile: :shock: :sad: :roll: :razz: :oops: :o :mrgreen: :lol: :idea: :grin: :evil: :cry: :cool: :arrow: :???: :?: :!: