How to make a trimmer snow blower?

Snow removal machine – automated mechanism designed for snow cleaning on open and hard-to-reach areas. It is represented by various modifications that differ in power parameters, the amount of energy / fuel consumed, design and other.

Garden trimmer – gasoline / electric tool designed to mowing herbs and fine shrubs on the garden plot. The line of their production is presented by models that imply use in manual and semi-automatic mode. The design of some devices allows you to modify them in such a way as to exploit this tool as a snow removal.

How to make a hangman from the Trimmer – tell me in this article.

How to make a trimmer snow blower?

Advantages of homemade snow blower

Creating a snow blower from the trimmer may be needed when the first is available, but there was a need for the second. Modifying will allow you to apply the same garden tool for various purposes.

The main advantage of the homemade snowpressure is the low cost of its manufacture. No need to acquire a specialized aggregate. Used homemade and / or purchased components, allowing to reorient the tool. Not every mower is suitable for re-equipment it in a snow blower.

Before starting this process, you should make sure of its expediency. To do this, it is necessary to estimate the characteristics of the existing automatic braid.

How to make a trimmer snow blower?

What trimmer choose?

For the manufacture of a snow blower will need a rather powerful unit. It can be made of electrical engineer or gas station. Often preference is given to the last. The reason for this is the technical characteristics of the first. The electric motor of such a device is designed for certain power loads. Non-target use can lead to his early way out.

How to make a trimmer snow blower?

The gasoline engine due to its design can work with a wide range of loads.

An important role is played by the design of the rod, a manual mower designed to transmit torque. Some of them are a curved tube. In such arcs, the transfer is carried out by means of a flexible cable. This engineering solution is not suitable for using the aggregate in order to clean the snow. Cable transfer will not cope with the load, which will increase at times in the process of cleaning snow precipitation.

How to make a trimmer snow blower?

A suitable version of the trimmer design will be the one that provides for direct transmission of torque from the engine to the working unit.

In such modifications, the driving energy is transmitted by means of a cardan shaft. It is significantly ahead of the cable equivalent of technical indicators.

How to make a trimmer snow blower?

For the manufacture of a snow blower You can use the wheel lawn mower. A model is suitable for two wheels and a rotating working element located in the front of it. Mower of a suitable configuration is shown in the photo below.

How to make a trimmer snow blower?

Four wheelchand is not suitable for alteration in a snowplow machine.

Tools and materials

A set of tools required for the manufacture of a snow blower may vary depending on the selected way of achieving the goal. Some homemade modifications imply not reusable use, others are intended for permanent operation.

Minimum setting tools:

  • Bulgarian;
  • drill and drill;
  • welding machine;
  • hammer, pliers, wrench and others.

How to make a trimmer snow blower?

How to make a trimmer snow blower?

How to make a trimmer snow blower?

How to make a trimmer snow blower?

    The ushm is needed for clipping the necessary parts from metal and subsequent processing: grinding, cleaning, sharpening. Drill – to drill holes for fastening elements: bolts, rivets, clamps. Inverter will be needed to weld all elements of the design.

    List of materials:

    • sheet metal (thickness varies depending on the selected design);
    • Cut pipes: metal, plastic;
    • bolts, nuts, washers;
    • Metal clamps.

    How to make a trimmer snow blower?

    How to make a trimmer snow blower?

    How to make a trimmer snow blower?

    How to make a trimmer snow blower?

      Metal sheets formed a housing of the drum, blades and a cleaner. Pipe is necessary for the arrangement of the directional snowstone. Through it will be released. Fasteners Threaded components are needed to fasten the structural parts of the collection-collapsible nature. Clamps can serve to attach the harvesting attachment to the trimmer bar.

      How to make a trimmer snow blower?

      How to make?

      Making a snow blower from a benzotrimmer does not imply a conversion of the mower design, and only comes down to the manufacture of nozzles. Consider an example of the simplest design of this removable element for gasoline trimmer.

      How to make a trimmer snow blower?

      Before starting the workflow, it is necessary to make appropriate drawings. They must take into account the dimensions of all parts and the methods of their connection.

      Production of the Baraban Case

      The hull of the drum is a metal cylinder, which diameter is greater than height. The magnitude of the diameter and the height of this “box” determines the volume of snow that will be discarded to the side. The case should not be too large, Since this can lead to a trimmer engine overload.

      How to make a trimmer snow blower?

      The drum is made by drinking from a metal sheet of the circle of the desired diameter and welding to it. This side can be made from the same sheet metal, cutting the tape from it, the length of which is equal to the length of the circle circumference. The welding is carried out in a point in order to avoid deformation of the workpieces due to the high heating temperature. After grabbing parts with welding to one point, the side bends over the edge of the circle, the point mount repeats. As a result, a certain round “Bowl” with a side should be obtained.

      The optimal diameter of 30 cm, and the height of the stern from 5 to 8 cm.

      How to make a trimmer snow blower?

      In the center of the bottom of the “bowls”, a hole is drilled, which is intended for fastening the drum on the body of the rotation gearbox to the trimmer shaft. The diameter of the hole for several units is larger than the diameter of the shaft – their contact is excluded. The drum is attached to the gearbox stationary. To do this, elongated nuts are welded to the gear case or the fasteners are used in the gearbox itself, if any. In the bottom of the drum drill holes, located opposite the equipped fasteners on the gearbox. Singing the hole with fasteners on the gearbox, you can fasten the drum to the working part of the trimmer.

      How to make a trimmer snow blower?

      In order for the drum housing to be firmly held on the trimmer, the focus is welded to the rear of the first. This element is a jumper connecting the drum with a Cardana Cardana tube. The jumper is attached to the tube with a clamp.

      Manufacturer of screw

      A disk is cut out of the metal sheet, the diameter of which is smaller than the drum diameter by 2 cm. In the center of the disk drills a hole with a diameter equal to the diameter of the trimmer shaft + 0.5 mm. 4 blades are welded to the reb. Their location – Cross.

      The blades should not come into contact with each other, leaving a free hole in the disk.

      How to make a trimmer snow blower?

      Disk with blades – Screw, rotating on the shaft, should not touch the bottom of the drum housing. To do this, the nut is screwed at the shaft, then the disc is dressed, which is fixed by another nut. The height of the first nut should be sufficient to leaning on it, the screw was in insufficient removal from the bottom of the drum and the bolts hats, which are fixed to the reducer.

      In the top of the drum (from the engine of the Trimmer), a hole with a diameter equal to the diameter of the snowstand tube. This pipe is welded to the edges of the hole, and the welded seam is carefully coarsened. Snower should be directed away from the unit operator. The optimal angle of inclination of the pipe, depending on the nature of the terrain, on which snow will be cleaned. It should be sufficient to jet snow reaching the desired length.

      How to make a trimmer snow blower?

      Front and bucket

      The facial part of the drum housing is half closed with a metal plate. Its fasteners should provide for the possibility of installation / removal. This is necessary in order to have the ability to periodically clean the drum from the alignment and for the removal of the trimmer nozzles. To do this, the “ears” with holes are welded to the drum housing through which you can attach the facial plate bolts. It should also hold holes located opposite the “ears” of the drum.

      How to make a trimmer snow blower?

      The bucket intended for the fence of snow masses and feed them on the screw is made of the same metal as the other details. It is a co-associated plate, welded / screwed to the bottom of the housing of the snow blowing nozzle. Its front edge must be sharpened in one-way. It is necessary to improve the breath in the simplifying snow.

      Bucket can also be made removable.

      How to make a trimmer snow blower?

      Additional Information

      All spanning bolt connections must be equipped with washers or grovers (if necessary). Screw blades shape – rectangular, with rounded corners.

      During the operation of a snow blower from the motocos, it is important to take breaks and give rest tool.

      How to make a trimmer snow blower?

      How to make a hangman from the trimmer, look in the video below.

      Rate article
      ( No ratings yet )
      Share to friends
      Rebuildhom.info - construction and repair, dacha plot, apartment and country house, useful tips and photos
      Add a comment