Motokos, they are trimmers, are popular. These budget vehicles can be applied in dachas, in personal agricultural farms, farms and the municipal sphere. However, the practicality of such devices can only be assessed by those who can correctly start their operation.
It should be noted that the gasoline spit is very controlled. Enough to see how other users use this unit to start using it fully. The implementation of the basic technical functions is intuitive and does not require any difficulties in practice. Properly rolling the gasoline trimmer will not be difficult. Moreover, almost absent is the difference between household and professional categories.
Key difference is the type of motor. On the technique for professionals, it is more powerful and gives more turns. The two-stroke engine is more often used in household models. Four-stroke aggregates are more reliable and issued greater effort, so suitable for special conditions, complex and overgrown areas.
In addition, it is necessary to take into account whether there is a supplied cutting device.
How to start work?
The literacy of the first start depends largely, how the gasoline braid will show itself during further operation. Errors can lower the devices of the device. The fact is that after the launch, the moving mechanisms of the work apparatus will be taken to each other. Additionally, the skills of using the trimmer are formed. This is very important in cases if you work with such a technique for the first time.
Start with an inspection of the gearbox and the quality of the coating of its lubricant. Then prepare according to the instructions fuel mixture.
IMPORTANT: Such a runoff will be useful not only when mastering new equipment, but also when preparing braids to work after winter storage. If there is no lubricant at all on the gearbox, the gear transmission will be susceptible to very strong friction. Because of this, they begin to warm and emit gears.
Noticing a shortage of lubricant or its absence, you need to add a portion of “Litola”. The procedure is carried out very simply: twisted the screw located on the bending of the camp. 1-2 ml of lubricant are added by the technical syringe through the released channel. In case of everyday work with a trimmer, 1 time in 8-10 hours will have to lubricate the rod reducer.
But running in the gas station is not exhausted only by the oil laying.
Two-stroke motors need a combustible mixture of two-stroke oil and gasoline. It is prepared in the proportion specified in the instrument manual or on the lubrication label. Fuel preparation should be made little to be enough for one pouch. Plant the stock of fuel needed to the following container:
- plastic canisters;
- Glass dishes;
- Metal containers.
Take oil recommended by a medical syringe. This will make it possible to accurately keep the dosage. Sometimes another question arises – the manufacturer of the instrument and the manufacturer of motor oils indicate the different proportions of the combustible mixture, so it is difficult to determine what instructions to follow.
The output is simple: you need to run the gasoline trimmer with the minimum possible amount of oil. All the same, the lubricant does not fade completely, and its surplus forms coke, clogging piston and cylinder.
After the end of the test and filling the fuel mixture, such manipulations should be made:
- Put the trimmer on a flat surface;
- shift the lever to the “closed” position;
- pump fuel into the carburetor;
- run the ignition system;
- smooth movements pull the allowing cord, waiting for resistance;
- Immediately after that, make 3 or 4 strong jerk;
- as soon as the motor starts working, open the damper.
How to achieve the accuracy of parts?
The newly described launch method is quite suitable for Chinese equipment. But sometimes the start from the first time fails either the trimmer immediately stalls. In this case, the same manipulations with a lifting duct valve are carried out. If and then nothing happens, you need to contact the specialists. If the system is working normally, running the device at once anyway should not.
First, the motor must warm up at idle for 5 minutes. Important: If another time is specified in the instructions, then it is necessary to follow its instructions. During the warming up, you need to adjust the air supply. Specifying the different positions of the air damper lever, ensure that the cutting part does not move. Waiting for the warm-up, open the flap completely and set the power of 50% of the maximum.
In this position, the lever holds from 20 to 30 seconds. Resetting gas to a minimum, allow braid to work 30-40 seconds. Then set the power of 20%, and are waiting for 10-15 minutes. After that, the motor muted and leave alone on the ¼ hour. When the trimmer cools out, the engine run is produced by the already described scheme, but with the initially open valve.
It is necessary to abandon the long-term gas delay, since poorly fitted parts may be damaged. Long work at idle turns is also contraindicated – it will lead to overheating. On this engine running is complete, then you need to run down the gearbox. This procedure is carried out in an open place where the soft fresh grass grows. It is kost from 5 to 10 minutes without a break, periodically gas to power 50-75%.
After such a session stop motocos for 20 or 25 minutes. Usually grabs 3-4 cycles so that the trimmer gearbox works for many years. Most often try to run the device until the first fuel refueling is completed.
But still need to monitor the temperature of the gear and motor nodes. After running, the oil must be changed.
Features of the Benzokos running in the following video.