If the oven fails, it seriously complicates life. Even competent care and regular cleansing does not ensure that the device will work without breakdowns. There are several standard signs that describe the most frequent situations of disorders in the work of the oven: it ceased to heat up, the lamp was broken inside, the gas is turned off periodically in the oven, dysfunctioning the control panel, the oven does not turn on.
Causes of bad heating
This is usually due to breakdown of the temperature sensor. This defect can be caused by different failures, it makes sense to disassemble every case.
Why the oven does not warm:
- The power cord has deteriorated – it may have impaired integrity;
- There was a failure in the operation of the switches;
- a fan broke;
- In sufficient fit of the door affects the heating.
When nuts nutrition, the oven is either poorly heated, or the temperature in it does not grow at all. To reveal the cause, disconnect the device from the power supply, make sure the cord is not damaged anywhere. Just in case you can check whether it is included in the working outlet. The situation when it was the outstanding socket becomes the cause of non-working oven, very common.
Even if a small defect is seen on the cord, it can be enough for the ovenslock to work. The whole system is tied to the cord, because we consider this option first.
Checking the work of the regulator
With a potential short circuit, a switch-regulator could fail. He and paralyzes the work of the oven. To make sure that the case is exactly in this, you need to perform uncomplicated manipulations.
- Disconnect the stove from the electrodist;
- Turn the power control handle first at the maximum, and then to zero;
- achieving limit values, the regulator must click or publish another defining sound.
Replacement light bulb in the oven
If the regulator does not respond to these actions, it needs to be replaced. For this, the rear panel plate is unscrewed, the mechanism is replaced. In order not to get confused in placing the handles and wires on the stove, the scheme should draw (and better – take a picture).
In some cases, repair the slab can be replaced by fan. But not always stopped the work of the fan – this is a strict need for a new one, sometimes quite well wipe it with oil components so that they do not fit together to each other.
Light bulb in the oven is designed for long exploitation. But if it burns out, you need replacement. Be sure to keep the paper instruction to the electric stove, because there is information about the size of the base of the bulb and its power.
To replace the light bulb, you need:
- Disable food technique;
- Remove the protective cap;
- Replace the light bulb on the recommendations specified in the individual instruction (in different models, the replacement algorithm may differ).
When purchasing a new light bulb, its main criterion will be high-temperature resistance. Almost always a landmark – 300 degrees. If the light bulb with a weaker indicator, it will break quickly.
Correction of stable shutdowns
Here is the case in a breakdown of the thermostat. This can happen due to overheating of the oven if the design of the plate does not provide for self-terminal functions when a certain temperature indicator is reached. The problem of the thermostat is solved. If there is even a small experience, you can do it without attracting specialists.
Electrical repair with automatic shutdown:
- Disconnect the slab from the network;
- Remove the power regulation knob;
- Loosen the mounts, take a picture of the thermostat connection scheme;
- Install a new temperature controller;
- Return the adjustment handles.
Some people are confused by a temperature switch handle with a thermostat – if you do not have enough information about the device and the work of the plate, it is wiser to contact the specialists.
Less often arises failure in the control panel. If you are the holder of the plate with such a modern functionality, do not care for the repair yourself. The device under warranty needs to be returned to the service, and if the warranty has expired, invite a specialist at home. Settings fails require serious professional diagnostics – as a rule, the problem is quickly adjusted by a specialist.
Diagnostics of Tan Fault
Tan is called the heating element looking like not too thick tube with wire from high resistance inside. Void tubes are filled with magnesia so that the wire does not touch its walls. In the wind wardrobes, the Tan are spiral, solid, halogen.
If you have noticed that one part of the dish proceeds well, and the second almost remains raw, the problem may be in a faulty. It is present at the top and bottom of the oven. If the part is working, it glows with uniform red light, heats up strongly. If it is faulty, heat is not highlighted, and on the surface of the heating element can be deformations, black spots.
You don’t need to change a tan with your own hands, you can only aggravate breakdown. Invite a specialist who dials the oven, and eliminates breakdown. Often the master notices and other concomitant problems. For example, he will see that a rubber layer has moved from the door in the right place. In this case, the specialist will glue an elastic band, which will provide the desired adjuncing of the doors to the case.
If the oven smokes, it turns off, it warmly warms, do not use it until the problem is eliminated. Do not try to deal with independent repair if weakly understand the technique. If the stove is still on the warranty, and you yourself try to fix it, in case of unsuccessful repair, the warranty service service may refuse you free repair.
To work for a long time and no complaints, you need to follow easy rules from the first days of operation.
- The inner surface of the oven needs to be cleaned delicately. Usually for this purpose, the owners take soft sponges. If you count on metal brushes, GAR is rubbed well, but the surface is quickly scratched.
- Cleaners are better to take creamy. Abrasive drugs are traumatic for the surface of the oven.
- If aluminum elements are present on the outer surface of the device, then even before washing it makes sense to lubricate them with sunflower (or any other vegetable) butter.
- Cleaning procedure should be completed with alcohol.
- Acetic solution is perfectly coping with strong pollution. If fat closets accumulated inside the oven cabinet, and the smell of it is not the most pleasant, you can put in a cold brave cabinet with one third cup of ammonia alcohol.
- Never put in the preheated oven dishes with a wet bottom.
- If the oven formed the solar fat, heat it up to 50 degrees, then turn off and wipe the surface with a soft damp cloth.
- All external parts of the electrophum wipes only in the disabled state of the device.
- Glass door Try to wash in conventional soap solution – if you do not start the process of contamination, soapy water is enough for high-quality cleaning. Do it costs once a week, then dirt will not have time to accumulate on the door.
Remember about the careful energy consumption: many cooks turn off the oven 5-10 minutes before the dishes are readily. The food is baked on the residual heat, and the cost of electricity is reduced.
With proper operation, the device serves a long time, at least 15 years. If the oven does not work in the electric stove, you can use the oven and the cooking surface separately, the alternative to the buyer today is abuse.
About problems in the work of the oven electrical stove can be viewed in the video below.