Repair of dishwasher do it yourself

About the possibility of repairing the dishwasher with their own hands once thinks every owner of this technique. Indeed, in most cases it is to understand why it does not work in normal mode, for which causes water, but does not wash, diagnose other malfunctions, it is possible without causing a master. You only need to pay attention to the failures that it turns out to be revealed in the process of the device.

Why the car is bad?

Among the troubleshooting of the dishwasher, which are pretty easily eliminated with their own hands, you can allocate a decrease in the quality of the device. It is expressed in the appearance of blessed drills and divorces on the walls of the dishes. Glasses and other glass objects after notching from the grid do not acquire crystal purity, remain muddy. The cause of problems can be a violation of the rules of operation of equipment. But much more often everything is just a bad selection of detergents.

In addition, the decline in the quality of the washing is always observed if the filters of the machine are polluted, clogged with mud and garbage.

Getting Started to troubleshoot, you need to act in stages, according to the following scheme.

  1. View dishwasher.
  2. Free her tick. Extract baskets and other third-party components.
  3. Unscrew filters from fasteners.
  4. Disassemble rockers sprinklers.
  5. Clear them thoroughly, rinse with running water, handle brushes.
  6. From the supply hose to remove the filter mesh. If it is contaminated, when rinking the water pressure weakens, the dishes are not washed quite carefully.

Having established all parts to the place, you can go to the study of other possible reasons for the deterioration of the device. For example, check the rinse tank. If it is over, glass and ceramic utensils when washing will remain with white powder divorces. Similar problems arise if a universal is poured into the container, and not a specialized agent.

It is worth carefully examining the recommendations of a specific manufacturer on the selection of compatible chemicals, and during the operation of the technique, do not violate them.

With severe pollution, the dishes need to be pre-processing strong contaminants manually. Maintains the value and order of laying. For example, lay in the upper tray of only cups and glasses. The bottom basket is intended exclusively for large-sized dishes, medium – for plates. Disturbing this order, it should be understood that the quality of washing will definitely worsen.

What to do, water remains inside the case?

For the first time discovering small moays of moisture inside the washing chamber, it is not necessary to scare. Water can really stay inside. Moreover, it is absolutely necessary to maintain a normal microclimate inside the device. This allows longer to keep elastic sealing gum. If a small puddle turns into an entire sea, a turbid liquid, with food residues, the problem will have to pay more attention.

The reason why water in the pallet is stared, one of the following faults may be.

  • Invalid connection of the exhaust hose. If it is located too high, you will have to solve the problem with the movement of the removal. It is necessary to reduce it by 35-40 cm from the previous position. After that, you can run the machine in test mode.

  • Block. It is associated with clogging of water filtration system. It is enough to clean her so that the problem is solved. In the future you need to repeat these actions every 7-14 days.

  • Broken pump or water level sensor. In this case, it will be difficult to cope. Replace parts better entrust to the service center specialists.

If the machine is not on warranty, and the breakdown occurred due to the pump (pump) or water level sensor, parts can be bought independently. They are original or copied – such options are manufactured in Asian countries. They are cheaper, but do not guarantee the staffing of the technique in the future.

Constantly turns off: solving the problem

One of the most unpleasant failures in the work of dishwashers can be called their sudden shutdown. Happens such a failure usually at the beginning or middle of the cycle. If a similar defect in the equipment is detected once, the cause can be a short-term failure in a program or a voltage jump. You can correct the problem by using a special stabilizer to connect equipment.

If the dishwasher is turned off constantly, the source of problems is the power supply system. You can deal with such a phenomenon in different ways. The first thing about to take care is to restart the machine. To do this, it is enough to press and hold the inclusion button for 20-30 seconds. If the current is able to stabilize, the process of washing the dishes is successfully activated.

In order to avoid possible “leaks” and interruptions in the power supply, it is enough just to properly organize the connection of technology. On the path from the outlet to the housing, it is better not to use various wiring elements or select models equipped with a fuse. Sometimes the frequent shutdown of the machine is associated with a breakdown of the Tan – water in this case will not be warm too. The heating element may be damaged by the sediments of a lime deputy, burn due to power supply breaks. Solution of the problem in this case will only replace the part.

If all these measures do not help, check the program block. Dishwashes it is most often suffering from voltage drops. Failures in this case will be permanent.

It is worth calling a specialist who reinstall software or suggest the replacement of the damaged device details.

Other malfunctions and their elimination

Dishwasher independent repair always begins with tracking all device cycles. Only so you can reliably identify the reasons for which one of the functions broke down. For example, if the intake valve does not work, the technique is constantly gaining and drains water. Secure such a breakdown Sometimes you can only looking at the water consumption counter. With an incessant set, it will work very actively, like a pump inside the case.

Much easier diagnosed violation of body insulation. In this case, when you touch the technique connected to the network quite significantly beats the current. Diagnostics of breakdown space better entrust professionals. Similar to the actions when damaged the control module boards. Consider independently you can only do those faults that do not require the use of specialized equipment. In other cases, especially if the technique is sicked, noise, shows other signs of non-standard work, it is worth suspending its operation, contact the service where they can diagnose and repair equipment without risk to aggravate the problem.

Unregulated plums

One of the signs that the technique just constantly picks up and drains water, is a noticeable deterioration in the quality of cleaning dishes. In this case, everything happens in normal mode: the motor works, water is poured and merges. That’s just instead of starting the wash cycle, there is a completely different process. Just scored water is just as quickly reset into the sewer. You can detect such a leak, if you control the consumption of fluid – the meter will show that this indicator is constantly increasing.

The reason for the occurrence of such a problem is a valve breakage on water intake. If it is faulty, the fluid supply continues even to achieve the maximum allowable level.

Automation fixes overflow, then starts the pump to drain. The procedure for liquidation of the problem in this case will be such.

  1. Rotate the valve responsible for overlapping water supply.
  2. Wait for her complete drain. Debt technique.
  3. Get to the inlet hose. Remove it, disconnect the installed filter.
  4. Check the performance of the inlet valve. It is done using a multimeter. If resistance indicators differ from standard values ​​(from 500 to 1500 ohms), the part will have to replace.

You can only reinstall the inlet valve in the event that a person has an experience of soldering parts. It is important to understand that any errors when interfering with an electrical circuit, which participates in the supply of an energy device, can lead to more serious breakdowns.

Do not dry the dishes

One of the main advantages of the dishwasher can be considered the fulfillment of the full cycle of the necessary procedures – from rinsing to drying dishes. If a failure occurs on one of these stages, the appearance of plates and glasses suffers. For example, the incomplete drying process will result in the formation of the surfaces of the flows, stains and divorces.

Figure out why the work of technology occurs in non-standard mode, you can independently. In most dishwashers, a condensation drying is used, which occurs due to the heat release of the cooled equipment.

If this happens too fast, water drops will evaporate slowly, leaving traces. The drying process in this case is activated, just a reunion of the sash. The reason for the low temperature of the water and the case is solely failure of the Tan, the thermal sensor – their replacement will completely solve the problem.

When using turbosushki in more expensive models of machines, the source of ugly spots on the dishes becomes a broken fan. It is he who pumps hot air inside the hull. Drying will resume normally only after replacing the fan for a serviceable.

Buzzing at work

Immediately Ambassador to install dishwasher Owners usually rejoice in each sound from the body of the equipment. But if with time the technique has become very buzzing, you will have to take the noise more carefully. Its often its source is a broken bearing installed on the circulation pump. Over time, it loses greatly in strength, collapses, requires replacement. The order of work in this case will be such.

  1. Disconnect the device from the network.
  2. Remove pallet.
  3. Loosen the clamps holding the pump. Remove it from fastening.
  4. Separate wires and pipes.
  5. Disassemble the pump by dismantling the heater first, then anchor and impeller.
  6. Find Bearing. Remove it and gasket. Replace with new consumables.

Repeat actions to update the bearing in active operation of the equipment need not less than 1 time in 3-4 years. Also, the source of the roe in the absence of other sounds may be a breakdown of the pump. In this case, the pump is removed by the same scheme. All its block changes, not separate details.

Do not wash off foam

When working dishwasher, processes replace each other sequentially. First, the main chamber enters the washing fluid, then the rinsing composition, at the final stage, they are replaced by clean water. Ideally, the foam should not be stored inside the tank. But sometimes she still turns out when the dishes are notching. Reasons for the occurrence of the problem of only 2:

  • disorders in the selection and dispensing of detergents;
  • Failure in the work program.

Elevated foaming – direct consequence of owner’s errors. If he does not pay enough attention to the manufacturer’s recommendations, the result will be deplorable. Tablets with a complex action also not suitable for all cars. And if their use is permissible, you will have to reconfigure the equipment for correct operation.

Does not warm water

Washing dishes using special equipment implies mandatory water heating to a certain temperature. If this does not happen, the quality of the equipment is significantly reduced.

When the washing machine does not heat the water, only TEN can be source. It will have to be replaced.

Flows

The cause of leaks in the dishwasher is quite obvious. If the water becomes in front, you need to check the sealing seals on the door. When liquid accumulation under the body of the equipment, it is worth checking the filters and blocks for a blockage, the density of fixation. If flowing is formed when the unit is turned off, you will have to pay attention to the bay valve. In the course of the work of the puddle can be formed due to the proceeded hose.

Almost all of these breakdowns can be eliminated independently. Where worse, if the tank or tray for detergents proceeds. In this case, only the element replacement will be required, sometimes very expensive.

Problems with door

When operating dishwashers, many users face that the door is not fixed in the open position. By default, this feature must be present in the technique of any brand. But sometimes it needs adjustment. If this is not done, the sash will automatically close, interfering to remove the contents from the tank.

Especially often the owners of the built-in equipment are faced with such a problem. Find on it the adjusting elements can be near the loops on which the door is in. Here is the design of:

  • springs;
  • cable;
  • loops;
  • Plastic blocker.

If a fixing element broke, the door in the open position will not stop. In this case, you will have to replace the cable or the entire system entirely. The door will have to fully disassemble.

Other signs of breakdowns associated with the fixation of the sash in a certain position also require the repair of this particular block. For example, spontaneously opening, the falling sash always indicates that the cable closer occurred or the springs.

Prevention measures

    Prevent the breakdown of expensive dishwashers in most cases, it is simply carefully examined by the instructions for its operation. There is always indicated by the frequency of cleaning filters, a list of compatible detergents is recommended. Optimally, if basic prevention measures will be applied after each use of technology. This will avoid many unpleasant phenomena.

    When cleaning the filter, the fine cleaning element is simply washed, pre-insulating for 10 minutes in a solution of liquid SMS for dishes. The grid, delaying the coarser particles, as well as the steel mesh behind it will be useful to rinse in this solution, and then rub the old toothbrush.

    Unestation of sprinklers in the working chamber is a sure sign that it’s time to re-install the water conditioning unit. The sprinklers themselves also have to soak in an aqueous solution of 9% of the cutlery, then clean the mechanical method. After which they are washed with hot water.

    Watch the video about repairing a dishwasher.

    Rate the article
    ( No ratings yet )
    Add comments

    ;-) :| :x :twisted: :smile: :shock: :sad: :roll: :razz: :oops: :o :mrgreen: :lol: :idea: :grin: :evil: :cry: :cool: :arrow: :???: :?: :!: