Why arises noise in the microphone and how to remove it?

Surely you encountered outsiders and background sounds while recording video or audio files. It is very annoying.

In our article, we will consider the reasons for the appearance of such sounds, as well as let’s stay in more detail on the ways to improve the quality of the microphone.

Why arises noise in the microphone and how to remove it?

Causes of occurrence

Any background noise and extraneous sounds during recording from a microphone can be caused by the most different reasons, they are hardware and software.

You can call the most common causes.

  • Low-quality or defective equipment can ring in itself. If problems arise with expensive microphones, it can be appropriate repair, while cheap models are better simply replaced.
  • Problems with driver. As a rule, the sound card driver does not imply a significant number of settings, and in this there are their main difference from the drivers of printers and video adapters. Diagnose such a problem accounted for by updating and reinstalling them.
  • Foreign noises when working in microphones can be associated with poor communication, in particular, weak Internet connection. This may be caused by the lack of signal or technical problems with the provider.

Why arises noise in the microphone and how to remove it?

Why arises noise in the microphone and how to remove it?

    Other reasons that cause extraneous noises during recording from the microphone are:

    • Incorption of equipment settings:
    • Microphone cable damage;
    • The presence of the nearby electrical appliances that can cause sound oscillations.

    Why arises noise in the microphone and how to remove it?

    Why arises noise in the microphone and how to remove it?

      As practice shows, in most cases the problem becomes the result of several factors at the same time.

      How to eliminate?

      If the microphone began to make noise during recording, you can take a variety of fault correction measures. Depending on the source of the problem, they can be software or technical.

      When recording

      If your equipment is embarrassing, first of all you need to make sure that there is a fairly stable connection to the computer and there is no overestimated input level.

      To check the condition of the connecting cable, need to gently pull it, If you hear the crack strengthen, then, most likely, the problem is in it. Besides, You need to make sure that the plug enters the connector tightly.

      Why arises noise in the microphone and how to remove it?

      We draw your attention to the fact that if the connector does not provide due density of the connection, then it may be necessary to replace it, since it will be pretty able to fit the contacts.

      To test the second malfunction, You need to measure the height of the input signal in the settings. Severe two main methods to correct the situation in real time: with the help of internal adjustments and external.

      Why arises noise in the microphone and how to remove it?

      With outdoor tools

      If the microphone is either on its amplifier, a special regulator of the incoming signal level is located, you need to scroll downwards.

      If there is no such device, then weaken the sensitivity of the equipment Using toggle.

      Why arises noise in the microphone and how to remove it?

      Through internal settings

      In the tray, you need to activate the speaker icon, after which go to the “Recorder” item. In the window that opens, select the desired tape recorder and by pressing the right mouse button in the hidden menu go to the “Properties” block. Then you need to use The “Sound Level” tab, There are two types of regulators: microphone and amplification. Try to reduce them, so you can achieve a noticeable reduction in noise.

      The source of unnecessary sounds often becomes Incorrect extension installed to record or error in the audio card settings. In order to correct the default audio frequency formats, you must pass along the path: the speaker-recording device is the properties.

      Why arises noise in the microphone and how to remove it?

      In the window that opens, you will see a list of permissible extensions – try setting one of the first three, as a rule, they are less susceptible to foreign sound inclusions.

      To change the card settings, You can use the RealTek app. In the control panel, you need to activate the Microphone tab and turn on the echo suppression feature, as well as noise suppression.

      Technical problem with drivers solve very simple. To do this, use the installation disk if it is. And if you do not have it, you can go to the manufacturer’s website, download, and then install all the necessary software. We draw attention to the fact that there are no special drivers for the microphone, so it is enough just to choose your PC model and on the page that opens with the additional program block to set the operating system version.

      Why arises noise in the microphone and how to remove it?

      The cause of extraneous sounds during recording can be more serious problems, namely:

      • violation of the integrity of the contact inside the device;
      • Interference in the membrane;
      • E-board failure.

      Why arises noise in the microphone and how to remove it?

      Why arises noise in the microphone and how to remove it?

      Of all the indicated problems only the problems with the contacts user can try to fix it. To do this, it is necessary to disassemble the microphone case, find a section of the cliff and using a soldering to eliminate the problem. If the membrane is damaged, it will be necessary to replace it. However, due to its high price, such a measure is relevant only for the highest quality equipment. If you have a budget technique, it will be more profitable to purchase a new installation.

      Elimination of the electronic board can only be eliminated by the service center specialists, Since in this case it is necessary to use the methods of accurate diagnostics to establish a fault site.

      Why arises noise in the microphone and how to remove it?

      Why arises noise in the microphone and how to remove it?

      Background noise

      If the entry was made in the room where there is no sound insulation, the user may encounter the problem of the rear background noise.

      Low-quality audio record sound is eliminated using software methods. In most cases, audio devices provide Special noise reducers, which may have the most varying degrees of accuracy and complexity.

      Why arises noise in the microphone and how to remove it?

      Users who want not only to remove interference in the microphone, but also seek to further improve the sound of the track without spending on this additional funds, you can put the program on a computer or laptop Audacity. Its main advantage – clear Russified interface and free availability of the entire proposed functionality. In order to activate the noise reduction function, you need to go to the “Effects” tab, and from there to “removing noise”.

      Why arises noise in the microphone and how to remove it?

      After that, you should select the “Create Noise Model” option, where you need to specify certain parameters of the interval containing foreign sounds and save them with OK.

      After that, select the entire sound track and start the tool once again, and then try to change the value of parameters such as sensitivity, the smoothing frequency, as well as the suppression system. This will achieve better sound.

      On this work is completed, you can save the resulting file and use it in further work.

      Why arises noise in the microphone and how to remove it?

      How to remove noise after recording?

      If you have already done a noise record, on which you can hear how the transportation is buzzing outside the window, the neighbors are talking behind the wall or the wind is turned out, then you have to work with what is. If extraneous sounds are not too strong, then you can try to clean the record with sound editors, the principle of action here is the same as we described above.

      For more serious noise reductions, you can use program Sound Forge. It is 100% copes with any outsiders, and, in addition, contribute to the leveling of electromagnetic oscillations that cause the electrical appliances nearby. The sequence of actions in this case looks in the same way as when the background noise is removed.

      Why arises noise in the microphone and how to remove it?

      Why arises noise in the microphone and how to remove it?

      Another effective audio file processing application is

      REAPER. This program has quite wide functionality for recording tracks and edit sound. It was she who got widespread in a professional environment, but at home, you can use this program, especially since on the official website you can always download a trial free 60-day version. Clear audio tracks from extraneous sounds in this program using the REAFIR option.

      Why arises noise in the microphone and how to remove it?

      Why arises noise in the microphone and how to remove it?

      Why arises noise in the microphone and how to remove it?

      For the overwhelming majority of users of Reaper more than enough. Some users assure that with this program, even the so-called white noise can be removed.

      In conclusion, we can say that there are a variety of ways to suppress extraneous microphone noise. In most cases, users are easy and simply reach the desired improvement in sound quality. It should be understood that even if the easiest way turned out to be powerless, it does not mean at all that all other actions will also be useless. You just need to easily adjust the software and set the operating parameters of the instrument.

      How to remove the microphone noise in Adobe Premiere Pro, look next.

      Rate article
      ( No ratings yet )
      Share to friends
      Rebuildhom.info - construction and repair, dacha plot, apartment and country house, useful tips and photos
      Add a comment