Fibro cement plates for facades: description and characteristics

The market presents a huge number of diverse materials for construction and repair. Even if you consciously limit the search only by options suitable for facades, the choice is very difficult. Every homeowner and novice builder will usefully familiarize themselves with the properties of a promising fibric cement plate.

What it is?

Fibroplitus helps to make the housing facade really flawless outwardly. Approximately 9/10 of the entire mass of the product accounted for cement, which allows not fear of deterioration of the environmental characteristics of the house. In this case, excellent strength is guaranteed by the introduction of the hardening fiber and fibra. These additives allow you to increase the operation time of the blocks and make them immune to corrosion processes.

What is important, fibrolite slabs do not light up, and it immediately highlights them among many other facade finishing options.

The material works canceled with high, and under reduced temperature. Biological and chemical impacts found in everyday conditions are not dangerous for him. The mechanical strength in general is guaranteed. Useful for the consumer also resistance to the action of visible and ultraviolet radiation.

Fibrocement is twice the lighter of ceramic granite, if you compare with siding, while facilitating the load on the foundation does not mean less reliability or leakage heat. The material itself is cleared, the main types of pollution during contact with the fibrocement turn out to be destroyed, after which the rain or snow is washing away their remnants down.

Parameters

Fiber cement plate has not only impressive specifications. It is able to imitate the appearance of natural stone, including granite. Mount the plates are quite simple, if there are at least minimal experience and basic construction skills. But if there is no complete confidence in your abilities, it will be more correct to turn to professionals for help.

The main advantages of such a coating are the following:

  • the minimum risk of lime output on the walls, since blocks are manufactured using an autoclave;
  • the disappearance of the need to prepare the wall and the correction of its disadvantages;
  • pricing availability with more expensive analog properties;
  • the ability to separate the facade in any season;
  • Covering of the main structural material from negative meteorological effects.

Modern technologies allow you to use fibro-cement blocks for the implementation of the most intricate formed decisions. There are all the possibilities to choose the perfect fit or the texture of the details. Unfortunately, to acquire a fibro-cement plate with a thickness of 8-9 mm will not work in any way, the maximum indicator is 0.6 cm; The width of the parts varies from 45.5 to 150 cm, and the length is from 120 to 360 cm. The popularity of such solutions is also due to their ease: a unit block is not less than 26 kg. And this not only simplifies construction, but also allows you to do without any lifting equipment.

Read more  All about autonomous boiler houses

It is very important to remember about the high water absorption indicator. It reaches 10% of the mass of the product, which leads to deformations up to 2% (insignificant for strength, but can affect the aesthetics and at the state of neighboring blocks, seams). Finally, the fibrotent block does not appear and does not cut it manually, so the electric tool should be used.

It is with a mass of the design that its indigenous flaw is associated. Lift such a block alone in principle may just hardly be comfortable and easy.

Where you can use?

  • Fiber-based slabs showed themselves from the best side where it is required inexpensively and with minimal load on the foundation mimic natural stone. No less demanded solutions that have species like brickwork.
  • Great fibro-cement plate for facades Ban and for finishing inland rooms in them. Similar structures are characterized by excellent resistance to fire. And some manufacturers additionally enhance it, achieving maximum security.
  • Many people have already appreciated all the advantages of mounted facade designs. A large and lightweight stove allows for the minimum time to finish all the work, close the slighteners of the surface of the construction. In production, these blocks are hardened, and they become very strong. Since the outer side is covered with acrylic and polyurethane, there is no risk even when mounting near the reservoir or in places where abundant precipitations fall.
  • To create ventilated facades from a fibro-cement plate, you do not need to make special efforts.

Laying without gaps is made by similar technology. The difference is that it can be limited to a single clamp and put the panels directly to the insulation. Such a measure reduces labor consumption and reduce financial costs. Regardless of the elect, pre-calculate the need for materials.

The following tools are needed for work:

  • profiles of diverse types;
  • self-tapping screw;
  • Dowel-nails;
  • Accessories, completing the external composition of panels.

Review manufacturers

  • Fully Russian product “Latonite” Name it is impossible. Its production uses the latest developments of foreign firms. But this is only a plus, as the company continuously improves the product and adds periodically new versions in its range.
  • If products are needed with maximum resistance to fire, it is recommended to pay attention to the modification Flamma. She perfectly manifests itself not only in the exterior, but even next to the hot stove.
  • Quality Finnish version is, of course, “MINEIT”. The plates supplied from Finland are not only decorative, they increase the thermal efficiency of buildings.

  • But fibrocement Japanese brand “Nichikha” It is worth choosing those who want to avoid shrinkage after installation and immediately begin the finish finish. Another brand from the rising sun Kmew does not boast such a characteristic. It has been produced for the fifth decade and absorbed the abundant experience of developers.
  • If you return to Europe again, there is worth paying attention to the Danish Cembrit, Proven in practice year after year compliance with the most stringent standards.
Read more  Layout of a house of 6 per 8 m with an attic: Fite with the benefit of each meter

  • But the use of blocks can also bring considerable “Craspan”. The company focused its efforts on the release of finishing materials for the facade and opened over 200 representative offices in Russia. So, you can acquire the goods directly, without intermediaries almost everywhere.
  • “ROSPAN” – This is another attractive domestic brand. In its assortment there are far from some fibro-cement plates.

How to choose?

When choosing fibro-cement plates there are a number of subtleties, which sellers usually silent.

  • So, Detail painted in production will be more expensive, But the unpainted anyway will have to cover the LKM, and it is not too easy to do it manually. Make fashion will be easy if you buy blocks from fibrcement, imitating decorative plaster. Especially popular among designers coverage “Oak Bark”. Not bad formed results also gives the use of the decor “Flock”, “Mosaic”, “Stone Crumb”.
  • When choosing it is useful to pay attention to the density and the specific mass of the material on its natural or artificial components. It is very important to think about suitable dimensions and geometric coating forms. In addition to the slabs themselves, you have to choose and decorative strips for them. Preference coloring under the tone of the main wall or contrasting colors depends exclusively from personal taste and design concept. If typical dimensions are lacking, you can order longer and broad planks, but not more than 600 cm.

For horizontally and vertically directed seams, as well as to decorate the corners there are special types of planks. Assessing the need for them, you need to pay attention to the following features:

  • general height of construction;
  • gabarits plates;
  • number of corners;
  • The number of windows and doors, their geometry.

  • The structure of the slabs does not necessarily be smooth. There are options in which marble particles add or create relief. The most practical size is 8 mm wide, it is also possible to buy products with a width of 6 or 14 mm. If necessary, get unusual dimensions or non-standard design will have to submit an individual order. It will necessarily affect the timing of work, and at its cost.
  • In the most responsible places and when finishing the facade of the bath It is recommended to use smooth plates with a colorful layer treated with flame retardants. The coating of the peasant stucco will like those who are looking for blocks with the longest possible service life. In addition, it is stronger than other options.

Siding on the basis of fibrcement “Blower”. But at the same time, he surpasses a simple wood resistance to fire, shape stability in various weather conditions and resistance to aggressive insects.

Instructions for cladding

Installation of a variety of types of fibro-cement plates, if different, then quite slightly. General technological approaches are stable anyway. The first step is to careful surface preparation. Although it is formally considered that you can not resort to it, responsible builders and experienced professionals never risk do. Removing the old coating and exposing the slightest irregularities, dismantle any details protruding for the contour, eliminate damage.

Read more  Peskobeton M150 brand

The next step is the layout of the labels where the brackets will be fastened. The mounting distance is 0.6 m in vertical and 1 m in the horizontal plane.

Most professionals and even experienced homemade masters make metal subsystems because the tree is not reliable enough. However, it largely depends on personal choice and because available to performers.

Before finishing a house from fiber-cement siding, it is required to prepare the heat insulating layer.

A typical solution in this situation is the use of fiberglass attached to a dowel with a wide hat. Plates themselves are fastened using brackets or nails. Select the appropriate way you can, focusing on the thickness of the blocks.

Purchase panels should be purchased with a margin, even a simple cutting under the exact size may affect 5-7% loss. The gaps of the plates are required to close the shaking straps, otherwise the maximum smooth junction does not get.

      So that the facade surfaces retain their attractive view for a long time, these planks are recommended to cover the sealant layer. Do not try to mount the panels from fibrotent on “wet” technology, it will only spoil everything. Making work with your own hands, you need to choose such a dowel that will be immersed at least 3 cm in the material. From the insulation to the tiles used always leave the gap at least 4 cm. The upper band of the panels is equipped with a ventilated substrate, which provides efficient air circulation. On the outer corners they put steel corners in the color of the main coating.

      When installing with grooves, kleimers are used, and only the attachment of the thinnest elements to the framework profiles vertically produced by self-draws, supplemented sealing tape. Installation step in this case is reduced to 400 mm vertically. Where the panel is attached, there must be a hole at least 50 mm from the external boundaries of the material. It is not allowed to create very large gaps both vertically and horizontally. They must be at most – 0.2 cm. Horizontal bundles, where decorative sump is used, it is allowed to do with a break in 1 cm.

      Read more about Montage Fibro-cement plates you will find out in the following video.

      Rate the article
      ( No ratings yet )
      Add comments

      ;-) :| :x :twisted: :smile: :shock: :sad: :roll: :razz: :oops: :o :mrgreen: :lol: :idea: :grin: :evil: :cry: :cool: :arrow: :???: :?: :!: